Search results

  1. D

    Reset board zanussi

    Could someone tell me the sequence of resetting my grans Zanussi ZWF 12070w1 as the start light is still flashing the error code is e51
  2. D

    Zanussi help please

    My gran also heard a loud noise when it stopped too this did not trip the rcd but I think it's related
  3. D

    Zanussi help please

    Cool this confirms what I've been reading. Am I right in thinking this is a costly repair and maybe worth buying a new washer?
  4. D

    Zanussi help please

    Zanussi ZWF 12070 W1. Error code was five red flashes and 1 green
  5. D

    Recommend

    4 bed house, bathroom with bath, bathroom with shower, 2 adults, 1 child and 1 on the way. 15 radiators Cold water flow rate 15lpm and 3 bar static pressure. Old boiler Alpha cd50! New combi to quote for any recommendations please.
  6. D

    Dolphin legacy

    Cheers guys. Any recomendations on replacement? I'm thinking Mira
  7. D

    Dolphin legacy

    Dolphin legacy 10.5kw shower boils until prv blows. Filter and water pressure all ok. Do you recommend new shower unit? Does anyone know if this is another make with dolphin label on it? Any suggestions of an adequate replacement?
  8. D

    G3 regulations discharge into Hepvo trap and plastic waste

    could someone please send me a link to the fitting used between the tundish and trap
  9. D

    Damp Proof Quote

    traced one of the patches to a 4 inch external wall in which next doors down pipe discharges to no drain so the 4 inch wall which attaches to my property is soaking up the water and then my outside wall pulls it in. sorry for poor grammer in a rush for sunday football
  10. D

    Damp Proof Quote

    terraced house, adjoining wall, 9inch solid wall, chimney in front room has been removed from the bedroom above but im sure its rising damp
  11. D

    Damp Proof Quote

    could you guys help me with estimating the cost of having my living room walls injected to fix the problem i have with damp. The wall in question is 7metres long including 4 small alcoves. Job description, remove skirting boards, chop out 1 metre high of plaster, inject the walls, then make...
  12. D

    hotpoint wd420

    the fan was completly stuck with fluff etc and the stat had tripped off. i cleaned the fan and reset the stat hey presto it works again
  13. D

    hotpoint wd420

    dryer not working anymore it runs the cycle but clothes not dry. do i need to clean the filter at the back or is it more likely the stat at the top or both? cleaned the sump/filter a few years ago i found about 95p in change along with one or two bottons lol
  14. D

    rocks1 can you help again?

    so ive ohms tested the compressor and have 16.5, 14.5 and 13 between all pins, the problem im having is the overload relay keeps tripping ive established both the start up relay and overload relay are ok so am i left with a broken compressor or ive read somewhere the defrost board could be...
  15. D

    beko ca5411ffs

    so ive ohms tested the compressor and have 16.5, 14.5 and 13 between all pins, the problem im having is the overload relay keeps tripping ive established both the start up relay and overload relay are ok so am i left with a broken compressor or ive read somewhere the defrost board could be...
  16. D

    overload relay keeps tripping off my compressor

    beko ca5411ffs. im assuming faulty overload relay or start relay or hopefully not broke compressor, whats your thoughts guys
  17. D

    defrost timer

    o sorry i forgot i changed the title, its a beko ca5411ffs cheers i called beko today they dont want to help
  18. D

    defrost timer

    check my earlier post headed "rocks please help"
  19. D

    defrost timer

    could someone explain the test for me in detail and fin dings i should get please
  20. D

    rocks1 can you help again?

    is that the capacitor that is connected to the compressor, can you buy this item separately? or this defrost timer issue is their any way i can check that? i'm still gonna call them just interested
Back
Top