Search results

Cheers you have been so helpful awbcm, maybe one day I can return the favour . The angle is 32.5 degree dont bother posting back now you knob as I have done the job. If you can`t help on here dont try and be a smartarse

Hello , I wonder if anyone can help ,I am trying to locate a new flush seal for my loo. It has a macadee centre push valve which is blue in colour,( I have already tried macadee no joy). The loo was bought from wickes about 6 years ago and they are not interested unless I buy a new...

HI, Can anyone tell me where you can buy joint kits for kickboards. I have two breakfront base units and i believe the kickboard needs to be cut at 32.5 degrees anngle. I have done this and the joints look good and have been sealed but when ever the mrs goes a bit heavey with the mop,they...

Thanks very much , yes the circuit board has beeen replaced by worcester and they refused to wire the room stat up, because a link had been installed by someone else.(how lame is that). I bought their bolier and have spent around £300 per year with them on parts and servicing and they wont...

Hi, can anyone help, I need to reconnect a room stat to my worcester 280 combi. A local plumber disconnected it as the circuit board was faulty and he spragged it to so demand for the heating. Its only three wires and I will ISOLATE the power before I attempt to do it,I would just like...

Hi, Heres a good one for you,I have two breakfront units which I need to fit kick boards to .Has anyone any ideas what angle I use to cut the kickboard and is there any better method of joining them together , other than mitre glue. thanks

Thanks for the advice mick, are they easy to free off. If it`s the one I am thinking about I think it`s located behind the control panel and has switches at the bottom and a toggle off it. Thanks

My boiler is heating up the rads when the hot water runs and the c/h is off , any ideas please!.

HI, I too have little knowledge about plumbing < watch all the plumbers reply to this now >. I had something similar and was told that the last rad on the circuit was used to vent pressure to to stop boiler over pressurising. Don`t know if this helps any.

I am having problems with my boiler, with central heating off on timer and room stat, when hot water is ran heat goes to the rads too. Started happening last night, I am not 100% but think the diverter valve could be stuck open, can the valve be stuck in both C/H and H/w MODE allowing heat...

Hi , the last rad to boiler gets hot when heating is off,I think its the boiler is purging heat to rads to stop pressure build up.<but I could be wrong>. I was going to try and fit another small rad in a cupboard or hall ,as the last one at present is in my young childs room and it gets...

Hi, I have removed a doorbell when decorating ,i drew the wiring diagram but yes i lost it. I have two white wires coming in from my meter box and alarm type wires too. inside the alarm there are 3 terminals marked 0, 1, 2 . I was pretty sure orange and blue alarm cable went to...

I think he means SPUR but the you knew that Breezer,I thought this was a advice forum not extract the urine forum.

Thanks for the education breezer but the fused SPUR is in the loft space behind my upstairs bathroom,so putting a switch on in would be a pain to switch it on I would be in and out of my loft. < BUT YOU WERE NOT TO KNOW THAT>. I will try running a cable to it and follow GAZ THE SPARKYS guide ...

Hi yes the spare is unused,I have done some electrical work in the house ,I always isolate the power and no I don't lick any live wires. The spare is unused it was put in for a saniflow by a qualified spark not an amateur like myself, and its the closet power supply . What I was asking...

Is it safe to and how would I do it?, I want to fit a new light and pull switch for a cupboard, the nearest supply is a unused fused spare. The pull switch has a L1, a common ,and a earth connection in it,would it be safe to wire from a fused spare and what way do the wires go ,eg can I put...