DIYnot
Local | Network
   DIYnot > Forums
Local | Network
DIYnot Network Local DIYnot Network Local  
  Forum IndexForum Index     RulesRules    HelpHelp     Join FREERegister Free     About CookiesCookies     SearchSearch     LoginLogin 

Hotpoint Aquarius WF560 - Flashing Wash Enhance Light


 
Post new topic   Reply to topic    DIYnot.com Forum Index > Appliances
Search this topic :: View previous topic :: View next topic  
Author Message
obie1

from United Kingdom

Joined: 10 Apr 2012
Posts: 3
Location: Essex,
United Kingdom

PostPosted: Tue Apr 10, 2012 5:40 pm Reply with quote

Hello,

Just joined this forum.

I have a Hotpoint Aquarius WF560 Washing Machine.

On application of mains power, after several seconds, the On/Off light will 'flash on/off' and so will the 'Wash Enhance' light.

The machine will go part way through the cycle, stopping in limbo at the rinse and spin phase.

Any ideas what this fault is? Or what these error codes mean?

Cheers, Ben.
Back to top
 Alert Moderators

If you do not want to see this advert, click here to login or if you are new click here to join free.
rocks1

from Puerto Rico

Joined: 30 Apr 2008
Posts: 5861
Location: Puerto Rico
Thanked: 994 times

PostPosted: Tue Apr 10, 2012 6:55 pm Reply with quote

f01 light 4, motor triac
f02 light 3 motor, jammed/ tacho
f03 lights 3&4 Ntc fault
f04 light 2. pressure sw stuck on empty
f05 lights 2&4, pressure sw stuck on full
f06 lights 2&3, N/A?
f07 lights 2&3&4 heater relay
f08 light 1. heater relay
f09 lights 1&4 eprom/setup error
f10 lights 1&3, pressure switch not sensing
f11 lights 1&3&4, pump/draining error
f12 lights 1&2, communication error
f13 lights 1&2&4, dryer ntc/ fan motor
f14 lights 1&2&3, dryer heater
f15 lights 1&2&3&4, dryer heater relay
f16 N/A
f17 light 4, door lock
f18 light 3 comms error (3 phase motor) power board

f1 and f17 share the same light in your one error fo1 pcb gone ex pcb from here http://www.emwelec.co.uk/index.php?action=category&id=
Back to top
 Alert Moderators
obie1

from United Kingdom

Joined: 10 Apr 2012
Posts: 3
Location: Essex,
United Kingdom

PostPosted: Wed Apr 11, 2012 12:17 pm Reply with quote

Hello rocks1,

Thanks for your reply.

You mentioned I need a new PCB.

Is that because the Heater Relay has failed, inline with f08 light 1?

I'm assuming light 1 is Wash Enhance?

Cheers, Ben.
Back to top
 Alert Moderators
rocks1

from Puerto Rico

Joined: 30 Apr 2008
Posts: 5861
Location: Puerto Rico
Thanked: 994 times

PostPosted: Wed Apr 11, 2012 1:11 pm Reply with quote

Yes correct. But just test heater first should be 25 ish ohms.
Back to top
 Alert Moderators
obie1

from United Kingdom

Joined: 10 Apr 2012
Posts: 3
Location: Essex,
United Kingdom

PostPosted: Wed Apr 18, 2012 8:15 pm Reply with quote

Hello rocks1,

Been away from home over the last week, need to get back on the case with this.

Could you tell me were the PCB is situated within the machine please?

And the best way of getting to it?

Cheers, Ben.
Back to top
 Alert Moderators
Search this topic :: View previous topic :: View next topic  
Post new topic   Reply to topic    DIYnot.com Forum Index > Appliances All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
Similar Topics   Replies   Views   Posted 
Hotpoint WF560 not completing the wash cycle 5 120 Sun Jun 12, 2011 11:04 pm
Hotpoint Aquarius wf560 led 1 and led 2... 10 100 Sun Jul 01, 2012 8:43 am
hotpoint aquarius wf560 11 960 Mon Nov 02, 2009 7:03 pm
Hotpoint Aquarius WF560 Front Load WM Error code 13 1880 Wed May 12, 2010 2:09 pm
Hotpoint Aquarius WF560 error codes? 8 2120 Mon Jun 23, 2008 7:20 pm


 
DIYnot
Find an Expert | Find a Supplier | Search DIYnot.com
Network | Advertising | Newsletter
DIY | DIY How To | @home | DIY Wiki | DIY Forum
By using this site you agree to our Terms of Service / Disclaimer.
Please read our Privacy Policy. Copyright © 2000-2014 DIYnot Limited.