Honeywell Galaxy G2-12 wiring
- Thread starter nay376
- Start date
Sponsored Links
...or look in the sticky at the top of this forum...Google, first hit for " galaxy G2-12 ", without the quotes, is the installation manual, pictures 'n all
Hi,
Thanks for all the advice so far. I've wired the alarm up and powered it on.
I believe the sensors are all working. 1k closed, 2k tamper.
However, i'm stuck in engineering mode. So i'm assuming there is a fault?
Is it because i haven't wired the telephone line?
Vin
Thanks for all the advice so far. I've wired the alarm up and powered it on.
I believe the sensors are all working. 1k closed, 2k tamper.
However, i'm stuck in engineering mode. So i'm assuming there is a fault?
Is it because i haven't wired the telephone line?
Vin
You mean 1k closed / 2k open - right ?
Any tampers will stop the system exiting engineering mode. The only way to exit with a tamper (and it's not advisable) is to 51.17.1 restart or power cycle the system and close the lid quickly.
Ensure that you set menu 56.1.10 (Line Fail) to 0 (No).
Any tampers will stop the system exiting engineering mode. The only way to exit with a tamper (and it's not advisable) is to 51.17.1 restart or power cycle the system and close the lid quickly.
Ensure that you set menu 56.1.10 (Line Fail) to 0 (No).
Sponsored Links
Sorry. Yes that's what i meant.
Turned telephone to 0 and did restart.
Asked for a user reset?
Still engineering mode.
Turned telephone to 0 and did restart.
Asked for a user reset?
Still engineering mode.
Is that a restart via the menu or a power down. To exit engineering type in the pin code then the escape key
That was a reset via the menu.
Alsi cut the mains power to the panel
And tried pin plus escape. But still engineering mode.
Any way to find out whats the issue?
Alsi cut the mains power to the panel
And tried pin plus escape. But still engineering mode.
Any way to find out whats the issue?
Hi,
I did as above but still in engineering mode when i esc.
Now i get status unset when i re-enter
Any ideas?
Thanks
I did as above but still in engineering mode when i esc.
Now i get status unset when i re-enter
Any ideas?
Thanks
Nope. Just goes to banner with date and engineering mode
It sounds like you aren't exiting as engineer.
Escape from the menu system. 'esc' repeatedly.
Press the digits for the engineer code, but instead of pressing 'ent', press 'esc'. Eg. 112233 'esc'
The system will say "CHECKING FOR TAMPERS". If it's not doing this, then you're not using the engineer code.
Escape from the menu system. 'esc' repeatedly.
Press the digits for the engineer code, but instead of pressing 'ent', press 'esc'. Eg. 112233 'esc'
The system will say "CHECKING FOR TAMPERS". If it's not doing this, then you're not using the engineer code.
Hi,
Its not saying "checking for tampers"
Just takes me back to this...
//www.diynot.com/network/nay376/albums/24745/94264
Its not saying "checking for tampers"
Just takes me back to this...
//www.diynot.com/network/nay376/albums/24745/94264
Hi,
I think i may have changed the engineering code.
I did as above and now i get checking for Tampers.
It comes up Keypad1 but i am unsure of how to resve this?
Thanks
I think i may have changed the engineering code.
I did as above and now i get checking for Tampers.
It comes up Keypad1 but i am unsure of how to resve this?
Thanks
Hi,
I managed to get out of engineering mode. The PCB switch on the keypad wasn't seated properly. Thanks for all the help and advice so far. I have just one more question if you would help?
How do i set up the system?
I don't want 22 Users, just one and the master code.
In addition, I have set zone 1001 as Final - As this is the Exit/Entry point. Is that correct?
I managed to get out of engineering mode. The PCB switch on the keypad wasn't seated properly. Thanks for all the help and advice so far. I have just one more question if you would help?
How do i set up the system?
I don't want 22 Users, just one and the master code.
In addition, I have set zone 1001 as Final - As this is the Exit/Entry point. Is that correct?
DIYnot Local
Staff member
If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.
Select the supplier or trade you require, enter your location to begin your search.
Are you a trade or supplier? You can create your listing free at DIYnot Local
Sponsored Links
