DIYnot
Local | Network
   DIYnot > Network
Local | Network
DIYnot Network Local DIYnot Network Local
 
 
View Sleepyhead's Friends
View Sleepyhead's Posts
Alert Moderator
Statistics
Profile Views:4328 views
Friends:1 friends
Signup Date:Apr. 2, 2006
Forum:
1,896 posts
Thanked:20 times in 16 posts
Recent Activity
2 months ago
Sleepyhead was thanked by AndyV2011 for a post made in Appliances
4 months ago
Sleepyhead was thanked by onion_soup for a post made in Appliances
10 months ago
Sleepyhead was thanked by Handgun for a post made in Appliances
11 months ago
Sleepyhead was thanked by miramira1 for a post made in Appliances
1 years ago
Sleepyhead was thanked by durks for a post made in Appliances
1 years ago
Sleepyhead was thanked by cro2oz for a post made in Appliances
1 years ago
Sleepyhead was thanked by verywindycindy for a post made in Appliances
1 years ago
Sleepyhead was thanked by Grahame794 for a post made in Appliances
Personal Information
Country: United Kingdom
Friends (1)  [ view all friends ]

DIYnot
Comments (36)  [ view all comments ]
jessie1 - 10:28 AM on Sep. 8, 2011  reply | message
Hi Sleepyhead - I have a Communication problem just replaced motor and back board any suggestions on how to get these 2 boards communicating would be gratefully apprciated.
bigfatdog - 6:56 AM on Oct. 13, 2010  reply | message
Hi Sleepyhead,
Seems your the man ( and hero ) to sort out or suggest the way forward with dishwasher problems!!

I too have an Ikea Whirlpool DWH B10 - this has just started giving a stubborn intermittant bleeping without cycle progress, the start button light then flashes 4 times.

The other blogs seem to suggest it may be a blocked drainage pipe?

I would very much appreciate your comments

Thankyou

R's

Bigfatdog
nomaxone - 5:04 PM on Sep. 18, 2010  reply | message
I have a Smeg DWG614SS dish washer. The appliance will not start. When you power up a number of lights come on at the same time and if you press start nothing happens. Also you cannot select a program to run....Help
unclefewst - 2:34 PM on Aug. 9, 2010  reply | message
hi sleepyhead, reading one of your posts, about the whirlpool dishwasher door, my sister in laws custom fit panel has fallen off, i could see that the plastic lugs come brackets were all chewed up on the back, so i have purchased two new brackets, however i cannot get the damm door to stay on, i think i am missing soemthing basic here, any help would be appreciated, dave in norfolk
KeithColder - 11:07 PM on Mar. 24, 2010  reply | message
Hi - Sleepyhead... I now the feeling. I am impressed by both your kowledge and helpfulness. I have a SMEg DWD612Css dishwasher that has the drain pump running constantly. I cannot find any on-line manual for trouble shooting. Can you advice.
I am guessing that the drain pump is receiving an eroneous signal and that is is most likely from a sensor of some kind in the sump - but have no clue waht anything looks like. Help!
strautman - 8:23 AM on Mar. 12, 2010  reply | message
Sorry this is the first time on this site and every post I read you are on it so I thought I would write you personally. I have a diplomat adp8342. I get three red lights going from left to right and 10 beeps it is the 1st, 2nd and third buttons. I have checked to see if there is any water in the bottom and no there is not. I have reset it by holding the program switch and even if i pick the rinse cycle once i close the door the three lights go off. It seams like the drain pump is runing and when i open the door everything is bone dry. thanks for your help.
balvine - 11:17 AM on Mar. 2, 2010  reply | message
Hi Sleepyhead. You helped me out three years ago. I have a new problem. Are you still around?
JB3508 - 12:51 PM on Jan. 5, 2010  reply | message
with reference to http://www.diynot.com/forums/viewtopic.php?p=1461784#1461784

Having same problem, have done all in this thread but still no go. It is fair to say that a reed switch is either on or off, so would be fair to say, to test the reed switch you could just complete the circuit by running a cable between the two connectors. Again this wouldonly be a test and not a solution but I am assuming that the control unit is not expecting a certain amperage to be returned and that the reed switch does not return varying signals? I am very new to this, first dishwasher/first problem and it is driving me completely mad! An new reed switch is coming in at £65.00 so need to be sure it is the fault here. Please reply and help me with this!
maddaff - 1:39 PM on Nov. 20, 2009  reply | message
Hi pal my diplomat ADT8322 keeps flashing and bleeping can you help by any chance already read about cleaning the filter but no good please help a woman in distress
katiedobbs - 9:44 PM on Nov. 12, 2009  reply | message
hi sleepy u seem to be a bit of an expert on washers so here goes haha. i have a whirlpool awz 410 stopped spinning, belt stil on after taking back off machine, very tight and looks fine, is there any other reason why the washer would just stop spinning? thanks in advance for your help . Katie
 
View All User

 
 
 
DIYnot
Find an Expert | Find a Supplier | Search DIYnot.com
Network | Advertising | Newsletter
DIYnot.com | How to... | @home | Wiki | Forum | Shop
By using this site you agree to our Terms of Service / Disclaimer.
Please read our Privacy Policy.