White 2.5 T&E

Hager · 24 Sep 2009

Hi
Has any one got any spare white 2.5 T&E that i could have or i you would like some money i can pay you it's just so i can that i supply off this consumer unit in the shed and keep with the cable colour.

Thanks
Jake

ban-all-sheds · 24 Sep 2009

Why does it matter whether it's white or grey?

You can buy white if you really want it:

http://www.screwfix.com/prods/74493...able/Twin-Earth/6242BH-2-5mm-Cable-100M-White

mikhailfaradayski · 24 Sep 2009

Focus, Wickes, B&Q and the like will probably all sell it by the metre.

Whats more, its doubtful they'll ask whether you intend to break the law with it.

stargazer · 24 Sep 2009

Use grey and festoon your installation with these attractive stickers

ban-all-sheds · 24 Sep 2009

That notice applies to core colours, not sheath.

Hager · 24 Sep 2009

Hello
I'll see the hardware stores
No thanks to the sticker it's just the sheath colour i need it white i know that the white cable and old colours are breaking the law to newly install

Thanks
Jake

P.S did the photos show up?

ban-all-sheds · 24 Sep 2009

Hager said:
No thanks to the sticker it's just the sheath colour i need it white

It's just a shed...

If you're so concerned about cosmetics that you're prepared to pay nearly twice as much for LSF cable (which AFAIK is the only way you'll get white), why aren't all the cables in conduit or trunking anyway?

i know that the white cable and old colours are breaking the law to newly install

1) There are no laws governing what colour the sheath can be.

2) If it's reasonable for you to use old core colours to modify or extend an existing installation which is in old colours then it's not unlawful.

P.S did the photos show up?

Where?

mikhailfaradayski · 24 Sep 2009

Hi Hagar,

Its not so much the colour of the cable i was thinking of, but more to do with what you intend to wire up. You mention shed and consumer unit, both of which give me some cause for concern.

p.s. no, i haven't seen any photos.

Hager · 24 Sep 2009

Hello
All i'm doing is putting in a second IP56 plug socket on the other side off the consumer unit. This is the unit i'm taking the socket off.

Thanks
Jake

Shed CU open

Hager
24 Sep 2009
1

Top shed

Shed CU open MK2

Hager
24 Sep 2009
1

Top Shed

londonboy · 24 Sep 2009

I hope this socket your installing has an rcd built in

Hager · 24 Sep 2009

Hi
No it will not be nor will the shed consumer

But this one is

House CU

Hager
24 Sep 2009
1

Thanks
Jake

londonboy · 24 Sep 2009

Thats good then...
leaving the house with no power while you walk all the way back in to reset the switch.

RF Lighting · 24 Sep 2009

I think someone must have been slipping me thick pills again, as I really can't for the life of me work out why the cable needs to have a white sheath

Hager · 24 Sep 2009

Hi
So it does not look different to the rest i like thing looking the same and tidy any way it don't matter now i found some

Thanks
Jake

ban-all-sheds · 24 Sep 2009

Hager said:
i like thing looking the same and tidy

So it obviously wasn't you who originally installed the shed CU & circuits...

Anyway - what size is the cable supplying that CU?

What is the rating of the MCB it comes off?

How far is the shed from the house?

How is the cable installed? I note that it's twin & earth at the shed end, does the same cable run between the house and the shed?

Are you using that type of socket because it's going to be outside?

diynot

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.

Are you a trade or supplier? You can create your listing free at DIYnot Local

White 2.5 T&E

Similar threads