A
AssociatedAlarms
And it is. The answer?
texecom premier 48
- Thread starter signum
- Start date
Sponsored Links
system config, at factory settings, your panel is currently configured to grade 3.
37 - Panel Grade 3
All options relating to PD6662: 2004/EN 50131-1 Grade 3 are
enabled automatically. Also, the Premier Anti-code reset
becomes a 6-digit number and all user codes can only be
programmed as 5 or 6 digits
to enable and change 4 digit code to 4 digit and use 4 digits, you need to activate grade 2:
Panel Grade 2
All options relating to PD6662: 2004/EN 50131-1 Grade 3 that
are not required for Grade 2 are disabled automatically. Also, the
Premier Anti-code reset becomes the standard 4 digit number
and all user and engineer codes can be 4, 5 or 6 digits.
37 - Panel Grade 3
All options relating to PD6662: 2004/EN 50131-1 Grade 3 are
enabled automatically. Also, the Premier Anti-code reset
becomes a 6-digit number and all user codes can only be
programmed as 5 or 6 digits
to enable and change 4 digit code to 4 digit and use 4 digits, you need to activate grade 2:
Panel Grade 2
All options relating to PD6662: 2004/EN 50131-1 Grade 3 that
are not required for Grade 2 are disabled automatically. Also, the
Premier Anti-code reset becomes the standard 4 digit number
and all user and engineer codes can be 4, 5 or 6 digits.
global / config options / no 37 grade 3/ untick for 4 digit code this may be a different option number depending on panel software version but will be somewhere around 37 if not.
Sponsored Links
aux tamper is on the side above bell connections that needs linking out and best way to deal with spare zones is to proram them to not used.
do you have a panic button ? is it pressed or wired incorrect ?
Hi all, still got a few problems with this alarm
.... Everything is connected up now. when i go to set the alarm i get a message saying panic button active and front door active. I think i must be missing something hear. the door contact is a knight yend 74 with resistors. i've attached 2 images one of the door contact and one of the panic button, both just having 4 cables connected. 2 alarm 2 tamper. Any ideas ?
.... Everything is connected up now. when i go to set the alarm i get a message saying panic button active and front door active. I think i must be missing something hear. the door contact is a knight yend 74 with resistors. i've attached 2 images one of the door contact and one of the panic button, both just having 4 cables connected. 2 alarm 2 tamper. Any ideas ?
if you go into the engineers settings press [9] this brings up engineers utilities press [yes] press [3] this brings up view zone status press [yes]
type in the zone number of the devices youre having trouble with. (001 for zone one, 034 for zone 34 etc)
It will tell you the status of the zone and also the resistance of the circuit. Let us know what the readings are.
Normally for door contacts and PA buttons you'd just connect 2 wires and they will do both alarm and tamper.
Do you have the wiring diagram supplied with these two devices?
Where in yorkshire are you?
type in the zone number of the devices youre having trouble with. (001 for zone one, 034 for zone 34 etc)
It will tell you the status of the zone and also the resistance of the circuit. Let us know what the readings are.
Normally for door contacts and PA buttons you'd just connect 2 wires and they will do both alarm and tamper.
Do you have the wiring diagram supplied with these two devices?
Where in yorkshire are you?
have you altered any of the zone configs for resistor type ? but as RF says you are better looking at the zone status from engineer utils first or twist your alarm pair and tamper pair together and check to see what panel says.
cheers for reply guys, The panic button already has had all the jumpers taken off apart from the one on bottom right which says normally closed.
ive just checked the zone status and got as follows
Zone 1 (front door) >65k active
zone 4 (panic button) >65k active
ive just checked the zone status and got as follows
Zone 1 (front door) >65k active
zone 4 (panic button) >65k active
DIYnot Local
Staff member
If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.
Select the supplier or trade you require, enter your location to begin your search.
Are you a trade or supplier? You can create your listing free at DIYnot Local
Sponsored Links
