What, if any, regulations have been flouted on this install

Not familiar with that particular entry system, but why are there 4 separate identical power supplies?
 
Sponsored Links
Decent entry systems have a single power supply for the entire system - one per handset is ridiculously wasteful, and won't scale to even a moderate number of units.
 
The system isn't the issue, it's the terrible way it's been installed :/
 
Sponsored Links
UPDATE : They have refused to correct any of it ! where to from here ....
Sadly it will therefore be down to the nursery to take legal action against the installers to force them to rectify their non-compliant and dangerous work.

As suggested earlier, a report to Ofsted might kick things off, as might you RIDDORing it. But if it's a private nursery be aware that what could well happen is that they are forced to close.
 
It's not clear that the children are in danger, or if they are that it could not be removed by locking the cupboard.

As for preferable or not, the danger probably needs a proper risk assessment, and closure means people out of work and parents losing childcare, which might mean them losing jobs. What increased dangers might the children face then? Parents using unofficial childcare? Children being left uncared for? Children going hungry? Children becoming homeless?
 
UPDATE : They have refused to correct any of it ! where to from here ....
Plan B, if you are suitably competent - quote for putting it all right at the same time as fixing the functional problems. Make sure you are scrupulous in separating the two so that you aren't later accused of misrepresenting the cause(s) of the problems to get extra work.
 
All true BAS. In reality, your "forced to close" might in reality be "forced to take action to reduce the perceived risk, e.g. locking the cupboard". Trouble is that Ofsted inspectors are not knowledgeable about electrical risks - they're still demanding those stupid 13A socket covers.
 
Thanks for the comments thus far.

...and yes the cables in the trunking should be segregated as the twisted pair does not meet the highest voltage present in the trunking (if I understand band1 and band2 circuits correctly)

So, in essence, and without going into any detail, it doesn't comply with BS7671 ? which should be enough to go back to the original installers with and let them figure out why (and put it right ! ), else have a report drawn up from a qualified engineer - but that's doing half the job for them !

Is there a government body that this/the installers can/should be reported to, in light of the fact that it isn't covered under part P ?
Pete, where is this Nursery area wise? The installer might be part of a Part P scheme though as has mentioned it's not classed as residential but if you found out if they are a supposed member to one of them you could report them to their body - i think they'd take an interest in the shoddy work.
 
I was going to say to report it with RIDDOR, but it doesn't seem to come under that. It should certainly be reported as it's plain dangerous - no questions about that.
Unless cowboys like that get attention from the authorities then there's little incentive for them to mend their ways as there's always a stream of new customers who don't know any better for them to fleece.
With this being a business-business arrangement, is it something Trading Standards would be interested in ? Is the business a member of any trade groups ?
 
Trouble is that Ofsted inspectors are not knowledgeable about electrical risks - they're still demanding those stupid 13A socket covers.
No they're not. They're leaving risk assessing of sockets to the nursery. They do not demand covers.
 
No they're not. They're leaving risk assessing of sockets to the nursery. They do not demand covers.
Try telling that to my Daughter!
The tick box is still on the inspection sheet!
Every time they come round she has to get the previous paperwork out which includes the printouts from here and the various links.
 

DIYnot Local

Staff member

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
Sponsored Links
Back
Top