Cutting down a wardrobe?

Keitai said:
It's cut down. As it's not flat and I used piece of ply as the fence for circular saw the saw slipped under the fence. In cases like this, is it best to hold saw tilted slightly upwards so it always presses against fence?


View attachment 232675 View attachment 232676
Click to expand...

I have a feeling that your tape measure might be out of a couple of millimeters...
 
Sponsored Links
Sponsored Links
JobAndKnock said:
In terms of sawing this sort of thing, you can either buy yourself a plunging rail saw and rails (expensive) or you can make yourself up a guide for your saw which can be clamped onto the material. This is basically a piece of 4 or 6mm plywood or MDF with a straight piece piece of 2 x 1 PSE softwood screwed and glued down one edge:

View attachment 233114

Just note that before using it "in anger" you need to make a trim cut to size base exactly to the saw. This type of fence or bridge should allow you to cut fairly uneven stuff with or without non-straight edges but without any need to reference the saw fence which is redundant for this operation as the left side of the sw base (for right hand blade saws, for left blade saws you run the other way with the right edge of the base against the 2 x 1). The guide does need to be clamped in place, though, before cutting
Click to expand...


Have the baton the furthest side from saw. My saw is left side so I'll make this jig with baton on right side
 
JobAndKnock said:
In terms of sawing this sort of thing, you can either buy yourself a plunging rail saw and rails (expensive) or you can make yourself up a guide for your saw which can be clamped onto the material. This is basically a piece of 4 or 6mm plywood or MDF with a straight piece piece of 2 x 1 PSE softwood screwed and glued down one edge:

View attachment 233114

Just note that before using it "in anger" you need to make a trim cut to size base exactly to the saw. This type of fence or bridge should allow you to cut fairly uneven stuff with or without non-straight edges but without any need to reference the saw fence which is redundant for this operation as the left side of the sw base (for right hand blade saws, for left blade saws you run the other way with the right edge of the base against the 2 x 1). The guide does need to be clamped in place, though, before cutting
Click to expand...
I'll knock up jig long enough to cut off bottoms of doors. Would u bother with longer cuts e.g. 2.5metre long cuts?

I'll also after fixing fence (baton) let the saw cut the ply off
 
Keitai said:
I'll knock up jig long enough to cut off bottoms of doors. Would u bother with longer cuts e.g. 2.5metre long cuts?

I'll also after fixing fence (baton) let the saw cut the ply off
Click to expand...
Yes, that's how i've done mine.
This way you don't need to be super precise when fixing the guide baton to the ply.
But you need a straight baton to start with.
Better if sliced on a table saw so to be sure is straight.
 
D

DIYnot Local

Staff member

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
You must log in or register to reply here.
Sponsored Links

Similar threads

M
Odd wardrobesize
Replies
3
Views
376
big-all
B
E
Help, Wardrobe falling down
Replies
3
Views
2K
foxhole
foxhole
K
Screws have come out of wood door - how to fix?
Replies
4
Views
951
karansaraf
K
T
Walk in Wardrobe construction
Replies
8
Views
1K
charliegolf
C
M
cutting ikea pax wardrobe
Replies
7
Views
20K
blup
B
Back
Top