I had a need to drain my new pressurised system to re position rads. I thought that I would be able to put new Fenox in via the filling loop with a funnel. Finished with more missing the system than going into it. Is there any easier way?
Adding Fernox to pressure system
- Thread starter Diyisfun
- Start date
Sponsored Links
you can get fernox in a cartridge to inject into the rads with a sealant gun 
you might be able to hire a dosing vessel and pump it in
Sponsored Links
If you have a look at this post //www.diynot.com/forums/viewtopic.php?t=13300&highlight= you can see my method. Probably not the best in the world but it worked for me.
you have been advised wrongly
Diyisfun - I have just replaced a couple of rads and filled up with Fernox using the cartridge applied through a vent. Next time I need to add Fernox though, I'm going to try using the bottled stuff and doing the following
1. Choose a suitable rad to apply the Fernox (could get messy!)
2. Close both valves
3. Open the vent
4. Remove the plug (from the other top corner of the rad)
5. Syphon off 1 litre
6. Add the Fernox through the vent or through the plug via a tube
I'm a complete novice though, so can any of the experts please comment as to whether this will work
I can't see why not, and since the cartridges are about a tenner a pop more than the bottles, I reckon it's worth a go
Cheers,
R1
1. Choose a suitable rad to apply the Fernox (could get messy!)
2. Close both valves
3. Open the vent
4. Remove the plug (from the other top corner of the rad)
5. Syphon off 1 litre
6. Add the Fernox through the vent or through the plug via a tube
I'm a complete novice though, so can any of the experts please comment as to whether this will work
I can't see why not, and since the cartridges are about a tenner a pop more than the bottles, I reckon it's worth a go
Cheers,
R1
Sure it'll work. You don't need to siphon the water out, you can just undo a rad union a bit and let it dribble out.
Easiest "rads" to add it into are ladder style towel rails which have vertical bungs.
One "pro" way if you do a few is to put a tank connector and bit of pipe into the lid of a bottle - just transfer the lid to the next new bottle. Makes it a lot easier.
Real plumbers have hydraulic pressure testers so can squirt the stuff in through the filling loop, pressure relief pipe - or anywhere handy.
Easiest "rads" to add it into are ladder style towel rails which have vertical bungs.
One "pro" way if you do a few is to put a tank connector and bit of pipe into the lid of a bottle - just transfer the lid to the next new bottle. Makes it a lot easier.
Real plumbers have hydraulic pressure testers so can squirt the stuff in through the filling loop, pressure relief pipe - or anywhere handy.
Thanks Chris.
To make the filling easier, I kept the old cartridge with the tube that screws into the vent, and I've taken out the plastic bit that gets pushed up to the front, so I'll use it as a funnel. I'm undecided whether this is recycling genius or cheap as chips
Since it will screw into the vent, I figured it would be almost "air tight", which is why I'd need to undo the plug opposite the vent to let air out and Fernox in, so I was syphoning out of the plug rather than undoing a union - if it ain't broke, I'm still reluctant to undo it!
To make the filling easier, I kept the old cartridge with the tube that screws into the vent, and I've taken out the plastic bit that gets pushed up to the front, so I'll use it as a funnel. I'm undecided whether this is recycling genius
or cheap as chips Since it will screw into the vent, I figured it would be almost "air tight", which is why I'd need to undo the plug opposite the vent to let air out and Fernox in, so I was syphoning out of the plug rather than undoing a union - if it ain't broke, I'm still reluctant to undo it!
I bought a dosing pot that allows me to insert leak sealer in the system with in a minute.
I have used in about 100 times over the past year, Its has paid for its self a long time ago.
If you want one call liam on 07765203606 they are about £29.00.
I have used in about 100 times over the past year, Its has paid for its self a long time ago.
If you want one call liam on 07765203606 they are about £29.00.
DIYnot Local
Staff member
If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.
Select the supplier or trade you require, enter your location to begin your search.
Are you a trade or supplier? You can create your listing free at DIYnot Local
Sponsored Links
