Search results

Did you have the front dismantled when you did this to get direct access to the contacts?

Hi, do you mean the actual burners on the top of the cooker or the rings to control it on the front? ( Apologies probably a dart question but I'd rather be sure) The tops fine as the glass cover was down so all liquid came down front if cooker

Hi allas the title says, my daughter spilled a full cup of hot chocolate over the gas cooker, it seems to have got into the ignition switch and shorted out the contacts so that it is constantly clicking. I've isolated the electrical supply to it to stop this happening. I'm looking to get into...

Also I should add that the tap does normally have a frost cover on it

Yeah that was my fear with this, that it's basically an easy but not very robust method of fitting a tap. In fairness it was my wifes hairbrained scheme. Tap is below. Just in case there is any ice in the pipework (been -8 here for a few days) I've left the white handle isolated and the tap...

Thanks mate. Yeah white handle is supply to tap. Out of interest, have you ever used these self cutting/self sealing kits before? I've been pretty wary since day 1 of interfering with it too much in case it causes a leak. Also, any idea what the screw on the side is? I wondered if it was to...

Thanks for that. Above is what I'm working with, anything here as a drain point?

Hi all I realise that garden tap questions are all the range this time of year but I thought I'd ask anyway. I have just isolated mine under the sink but can get the actual tap to open to drain down. essentially I know have a volume of water in the pipework that is isolated at both sides, is...

Issue is that I want to see and get access to the inside of the external wall. At the moment I can remove the kickplate and feel a draught but can get close enough to the wall to see where it's coming in

Thanks all for the replies. The picture below shows the cupboard I want to take the back out of. Please ignore water damage on the front

Hi all I have standard kitchen units, I want to get access behind) below them to try to identify source of draught. To do this I'd have to carefully dismantle carcass, leave sink/worktop supported in place and then rebuild. Is this feasible for someone with limited DIY experience?

Hi all The wood above is under my uPVC front door, there is a reasonable gap to the floor. I don't know what is under/behind this but there is quite a bad draught getting in through it. I'd like to draught proof this, I'm thinking about just sealing with silicone but not sure if there's a...

Hi, thanks. I think I will avoid disturbing it any further for now just in case although I did re-read your initial comment about asbestos insulation not being used domestically which is reassuring. Funnily enough I was actually attempting to just that tip regarding pulling back the insulation...

Hi thanks for the reply. I was talking about the stuff of the "floor" of the loft. Basically there's modernish yellow/standard insulation on the top layer but after I pulled that back there's much darker stuff, not sure how clear it is on the photo but you should be able to see there's maybe 3...

I was trying to pull back insulation in my loft earlier to get some better airflow and this darker coloured insulation down at the eaves seemed to come away in my hand. I'm a bit concerned it's something that shouldn't have been interfered with, any ideas what sort of insulation it is? House is...

Hi I have an issue with where steam from my bathroom is going up into my loft and causing issues. I want to install some extraction for the bathroom. I was thinking about an inline extraction pump in the loft (to save having to drill through external wall at high level). I assume I would drill...

Sorry only just see this reply (email went to spam for some reason). Cheers, I actually forgot that the 2nd time I tried I did use mapei however I absolutely mixed it by uneducated judgment which is probably the issue. I'll try what you said and let you know, cheers again

My upstairs bathroom floor tiles are an absolute mess, we're putting the house on the market so wanted to try and tidy it up a bit. I twice tried to re-grout using some no nonsense stuff for floor tiles. Basically I removed what I could of the old stuff, mixed up the new and left for about 13...

No stickers in any of the cupboards unfortunately. Cheers for the suggestion I'll have a look just now

Bit of a hail Mary here but I've had no luck finding replacement doors online. I'm hoping these are quite generic and someone might know the name of the style or colour?