Search results

  1. D

    Cooker area refurbishment.

    Hello all. I have just removed a built in electrical cooker which was built into an old fire place. Removed all frame works and took back to original surrounding. Above were coo why xxker was is a sheet metal plate see picture. We are putting in a stand alone electrical cooker. As you can see by...
  2. D

    Confirming system and install

    My question may have sent mixed message. I would call local DNO regarding fuze. The consumer unit MCB are BS3871which are no longer allowed as per BS7671, is the best option fitting a 1way CU 63amp RCD and a 40amp for the 9kw shower. 10mm cable to 40amp double pole switch installed in cupboard...
  3. D

    Confirming system and install

    Hi all been requested to install a shower into house first time I have not had spare fuse in situe normal just stick to upgrading replacing current systems ins fuse system is BS3871 no extra fuse in spare slot so the obvious choice is installing a second consumer unit. I reckon the system is a...
  4. D

    Warm radiators whole house

    If I'm correct In saying the return on the new radiator has to be taken out and moved behind the T in for return to boiler and cylinder.
  5. D

    Wiring boiler in control centre

    True it may be old but it works perfectly so not replacing it
  6. D

    Warm radiators whole house

    Hi all Just had a radiator added to system since the radiators are warm. Would the position of the T in to current system have an effect have attached diagram of pipework. Advice would be welcome. Were the red is missing sellotape over before adding colour
  7. D

    Wiring boiler in control centre

    Blind as a bat thanks for the advice from you and @EFLImpudence
  8. D

    Wiring boiler in control centre

    This is my control centre this is why I was asking. Had issues since it was put in. Was looking at getting rid of links lnt and using it as a 10 way block
  9. D

    Wiring boiler in control centre

    Boiler is 10+ years old no name on it as I can find was in when we moved into it in 9 years ago and definitely only 3 wires in flex
  10. D

    Wiring boiler in control centre

    My boiler has only a live. Natural, and earth. How does it conect to the system without a SW.l feed
  11. D

    Hot water too hot

    No problems at all.
  12. D

    Hot water too hot

    1st one is the boiler 2 cylinder stat
  13. D

    Hot water too hot

    No disrespect what will that achieve. If I may ask?? Working at the momen
  14. D

    Hot water too hot

    Cylinder stat is a honeywell has positions. C - which I have a brown wire attached to and goes to terminal 14 Com - which I have a blue wire attached to terminal 15 as per schematic picture The 2 white flex is the connection for cyl stat.
  15. D

    Hot water too hot

    Yes iv taken down to 40 but it's still too hot at the moment it is completely turned to the off position and will leave it till late afternoon to and check water temp.
  16. D

    Hot water too hot

    Hi all. I have a gravity feed system, have just fitted a adey Magna clean in-between my zone valve as no access to return pipe to boiler. My cylinder stat is new and set to 60. But water is red hot. Emersion heater is switched off Zone valves seem to be working as levers are tight when no demand...
  17. D

    Control box connection

    Hi all. Not a heating engineer my boiler has no switch live. Earth/Neutral no issues with that one. My question is do I connect it to permeant live in box or as per the diagram inside lid which says It has to go into the terminal for the SWL but my Schematic says it should go into permanent...
  18. D

    Programmer connection issues

    Connected programmer but when I switch on the mains input the programmer will light up and then the fuze blows
Top