Search results

  1. B

    corgi

    You'll need NVQ 2 as a minimum. You will also need to compile a gas portfolio whilst working under the supervision of an existing gas fitter. After you have this you can undertake the ACS assessments, and then proceed to register with the new gas safe register. There are plenty of places...
  2. B

    Corroded BBU heat exchanger

    Yes the pic is above! I worked out how to attach
  3. B

    Corroded BBU heat exchanger

    Hello, I serviced my mums BBU today. It's a baxi bermuda, which hasn't had a service for two years. The heat exchanger isn't in great condition, it is corroded on the right hand side and has sagged, as you can see in the picture. My opinion is that it might be better to replace the boiler...
  4. B

    Update on WB danesmoor

    They want me to go back to fit some rads and a vanity unit :D
  5. B

    Update on WB danesmoor

    Hello, Fixed it :D New motor and pump, and it's running sweetly. Only took me urm.... 12 days :o
  6. B

    Oil burner motor

    Thanks for the info. Yep i'm still playing with the danesmoor. To be fair it hadn't been serviced in 4 years, and I needed to wait for the homeowner to remove worktop so i could access it. I'll get it fixed eventually :D Atleast i know what the fault it now :)
  7. B

    Oil burner motor

    Hello, Does anyone know what motor the electro inter b9b burner takes? Or where on the web I can find out. I stupidly didn't write down the part numer when I was at the job. Cheers.
  8. B

    Worcester danesmoor

    Thanks Stone, I was browsing the worcester site last night. I'm going back to the job to take a more thorough look, and hopefully I can find the fault. Cheers for the help.
  9. B

    Worcester danesmoor

    I've been to Mary Poppins and Next, but they just gave me a strange look :shock: I've found some good mail order sites for spares, and of course my merchant. I might just put a new burner on though :wink: I'll make more money that way :wink:
  10. B

    Worcester danesmoor

    I am OFTEC registered. I'm obviously newly qualified as a technician....we all start somewhere. Cheers for jumping on my back! Hmmm.... so where do I source spares? I'm aware there's more to an ignition sequence than a fan. The solenoid is ok, photocell is ok too.
  11. B

    Worcester danesmoor

    I've been to a danesmoor 15/19, the motor runs but I couldn't hear the fan, it then goes to lockout. I thought the fan was bolted to the end of the motor. Does replacing the fan sound like a good idea? Also does anyone know where I can get spares from? Thanks.
  12. B

    Sorting out an airlock

    Thanks for all the advice. I tried running the pump with the boiler off............and what do you know, the pump doesn't run. I took the pump off, and the impeller was clogged up, I gave it a little clean, replaced it and all was well.
  13. B

    Sorting out an airlock

    Is it possible to pulse the pump with the boiler off?
  14. B

    Sorting out an airlock

    that goes without saying!
  15. B

    Sorting out an airlock

    Hello, Fitted a couple of radiators on a microbore system today. It's a vented system, and the downstairs rads are all on drops. I've filled it up, but when the boiler fires up there's a noise from it like a boiling kettle, some banging, then the boiler cuts out. The flow pipe on top of...
  16. B

    Boiler doesn't fire on heating

    Thanks for all the advice. You're right Dave there is no anti gravity valve fitted.
  17. B

    Boiler doesn't fire on heating

    The programmer has a heating and a separate hot water switch. The rads get hot when hot water only is on.
  18. B

    Boiler doesn't fire on heating

    I did check it before doing any work, and the customer knew it wasn't working correctly. There is no 3 port valve, the hot water is gravity, there's just a pump on the heating circuit.
  19. B

    Boiler doesn't fire on heating

    Hello, Just finished fitting a bathroom at a customers house. They have an old boiler, an Ideal W wall mouted with gravity hot water. The boiler fires up when the hot water is on, but doesn't fire when the heating only is put on, and the rads get hot when hot water only is on. Any ideas why?
Top