Search results

  1. N

    Leaking toilet

    Have you tried to tighten the nut?
  2. N

    Do i need to connect to the manifold (where would it be)????

    What is an AAV? I have had a look under floor boards and the 22mm pipe after the pump tees off to 15mm in both directions of the house and there is no manifold as it tees off in 10mm to all the radiators as travels under the floor boards. Someone told me I should not tee off a 10mm as it...
  3. N

    Do i need to connect to the manifold (where would it be)????

    Hi there, I have just fitted a radiator in an extension. I have tee'd off the drop down pipes in the wall (feed and return) to the rad in my dining room. The pipes where 10mm and have used 10mm on the new rad. After bleed in my system all other rads in house work fine! The rad in the...
  4. N

    Accenta Mini Gen4 loop tamper

    I see what you mean. Would this one be any better as they are all about the same range give or take a couple of meters? larger image Texecom Prestige AMDT Plus £23.96 Grade 3 anti-masking digital dual technology detector. Features fully adjustable microwave range and digital PIR...
  5. N

    Accenta Mini Gen4 loop tamper

    4 METERS BY 6 METERS
  6. N

    Accenta Mini Gen4 loop tamper

    Will this one do the job? Honeywell Intellisense DT 7450 14m x 18m K band Dual Tec
  7. N

    Accenta Mini Gen4 loop tamper

    What is the best type of pir to get for a Conservatory? i know it needs to be PIR and microwave technology. Thanks
  8. N

    Accenta Mini Gen4 loop tamper

    Yes they are useful! And could have saved me time on other jobs to. Thanks for your help and advise. I will give it a go or get a new pir as i need to get a dual one for the conservatory and swap them over. Thanks
  9. N

    Accenta Mini Gen4 loop tamper

    Write i have the meter readings on the zones The total was 22 ohms on the loop. Below is the nearest to furthest away from panel- These readings were from the panel end. Utility pir room was 1 ohms Kitchen pir was 1 ohms garage pir was 1 ohms Back door 1 ohms Dining room pir was...
  10. N

    Accenta Mini Gen4 loop tamper

    Can not check wire runs as they run under floor boards as some of the cables are from when house was built a few years ago. Opened all lids and checked connections and springs all seem fine!
  11. N

    Accenta Mini Gen4 loop tamper

    Breezer do you think the problem will show as it has only done this twice and may not be present at the time i check with the meter. Or should the cause of the problem show?(as an unstable reading) Just a quick one i have been looking at other subjects members have been listing about...
  12. N

    Accenta Mini Gen4 loop tamper

    breezer what type off reading on the meter should i be looking for? ie the fault.
  13. N

    Accenta Mini Gen4 loop tamper

    Ok will lend a meter off my mate and have a look, could it be a faulty pir or something? Cheers
  14. N

    ACCENTA Mini Gen4 - No Part Set Programme

    Oh.... Did not look at the date!!
  15. N

    ACCENTA Mini Gen4 - No Part Set Programme

    the engineers code for the alarm is set at 9999 if it has not been change by the installer. If you have an lcd keypad fitted it is not that hard to set one up by flicking through the options. select program 1,2 or 3 by pressing the number you want. Then press the arrow up to flick through the...
  16. N

    Accenta Mini Gen4 loop tamper

    Any idea's I fitted an accenta mini gen4 alarm about 2 weeks ago without any problems using all 8 zones with pirs and door contacts also fitted 2x RKP's. After a week the alarm went off as i was watching the tv, the alarm was unset and was displaying on the lcd keypad tamper loop as i...
Top