Search results

  1. H

    Honeywell G2-20 - BAT MISS fault (have replaced battery)

    Hi, thought I would provide an update in case anyone else experiences the same issue. I had a separate conversation with GalaxyGuy which helped me out a lot with this issue. Thanks GalaxyGuy I did notice that the negative connector that connects onto the battery felt slightly looser than the...
  2. H

    Honeywell G2-20 - BAT MISS fault (have replaced battery)

    Thanks for the response. I will take a look at this later on this week. Was really hoping it wouldnt be the PCB :-(
  3. H

    Honeywell G2-20 - BAT MISS fault (have replaced battery)

    Hi, sorry for the late responses Bigsosij - I did check the connections and they are tight. I couldn't see any obvious signs of corrosion Gibbies - Its reading about 13.5V Still getting the same fault. I have changed the alarm settings so I can set it with the battery fault for now The only...
  4. H

    Honeywell G2-20 - BAT MISS fault (have replaced battery)

    I just checked, the leads do have voltage (reading 13.52V)
  5. H

    Honeywell G2-20 - BAT MISS fault (have replaced battery)

    Hi I have had a Honeywell G2-20 for nearly 5 years now and have previously replaced the battery a few years ago as I was getting a BAT MISS fault on the alarm. Recently, I started receiving the BAT MISS fault on the alarm again so I purchased a brand new replacement Yuasa NP7-12 battery from...
  6. H

    Internal sounder for Honeywell G2-20

    Thanks for responding. I just wanted to be 100% sure I was wiring correctly Appreciate your time
  7. H

    Internal sounder for Honeywell G2-20

    Hi GalaxyGuy Thank you for the response and sorry for the late reply. I just wanted to double check that the GND goes to the bell symbol for the SAB Connections below. I already have an external sounder so I am guessing both the external sounder and the internal sounder will both have a wire...
  8. H

    Internal sounder for Honeywell G2-20

    Hi I would like to wire a internal sounder to my Honeywell g2-20 alarm. It's a CQR SO/ALTO/WH/G sounder I have attached a pic of the terminals Please can someone tell me which wires on the internal sounder go to which terminal on the Control Panel Any help would be much appreciated Thanks
  9. H

    Honeywell PIR IS312B Wiring - help please

    Thanks have out the resistors in as per above and is now working
  10. H

    Honeywell PIR IS312B Wiring - help please

    Hi After some building work, we have had to replace a pir on the alarm and I can't figure out the correct wiring for it. I have a Honeywell galaxy G2-20 and the pir is a Honeywell IS312B. The other pirs connected to the alarm are a mix of pyronix etc and are working fine. The yellow and blue...
  11. H

    Scantronic 9800 not arming

    Thanks sparkymarka, your comment re whether the alarm panel pcb was a plus helped me. It looks like somehow 13 was marked as a zone (even though it's not active) so I went into engineering mode and corrected it. The reason why your previous suggestion (to omit 13 when arming) did not work for me...
  12. H

    Scantronic 9800 not arming

    Thanks, I did try your suggestion, unfortunately it did not work. The alarm goes off This was working fine a few months ago, it only stopped working recently
  13. H

    Scantronic 9800 not arming

    Sure, have uploaded the pic. Thanks
  14. H

    Scantronic 9800 not arming

    Thanks for the reply...picture of keypad attached
  15. H

    Scantronic 9800 not arming

    Hi I have a Scantronic 9800 alarm and need some help please Whenever I arm the alarm on A, 13 is displayed on the keypad, when I then open and close the front door, the number 1 is displayed. However, it then displays 13 and the alarm then goes off displaying EF (exit fault) on the keypad The...
Top