Search results

After all that, it was a simple issue with the receiver programming. A reset and fresh programing of the transmitter and we have operational bollards. I can now concrete them in knowing I wont be breaking them out again. Thanks for the help.

Jump from 3 "Common" to 4 "Open" and 5 "Close" = nothing Common to radio also nothing. Is there a way of checking the receiver module is giving the command to the control board? Red LED flashes when I push the button but nothing on the board. I would expect LED 6 "Radio" to flash. Under the...

Do you mean Jumper from connection point 13 to point 4 (if motor wired correctly) or 5 if wired in reverse?

4 wires from the limit switch. Connected to points 11, 12, 55 and 56 as per the vigilo diagram. It doesn't show anything i to point 13 "common" should this be bridged in any way?

Led 9 is lit which confirms bollard is lowered (which it is). They are the standard version.

Hi, Would anyone be able to advise what I am doing wrong with the controls wiring for an automated gate/bollard set up. I have the following that I am trying to set up; Fadini Vigilo bollard Elpro S20 control panel VIX 53 Transmitter & Receiver I believe all has been connected as per the...

Having had a further look today, if I stitch in another brick to each of the piers making them slightly wider either side of the drive, it will change the bollard centers and allow them to site beside the cables. This will mean no moving / capping /touching required. I get if a vehicle hits...

I will not be touching anything. I now plan to scan both to see which is live then give UKPN a call. Hopefully just need 1 capped off and nothing moved.

If i can get my hands on a CAT scanner, that should confirm which is live and which is dead as a start?

In hind sight I should have dug the holes before purchasing the bollards but i did not expect to be this unlucky, but they are here now and were not cheap so I am in an awkward position. The automatic bollards seem to require a silly depth. 900mm for a 500mm bollard. If the 2nd is a dead...

This is going from bad to worse. Had another look this morning and the bollard will go in beside the cable with no movement required (comments regarding the bollard being struck are noted). I then cracked on with digging the hole for the 2nd bollard. Almost done and I hit something in the...

Ok. Sounds like i need another measure up in the light to see if I can get away with making it work by squeezing it in next to the cable. We are talking less than 100mm so I will have to try and make it work another way. Thanks everyone

It would require introducing a 3rd bollard which would be a final resort and one i want to avoid if at all possible

Hi, Firstly merry Christmas to everyone. I hope you had a good few days rest. I am installing electronically retractable bollards in my drive before I have the resin bound gravel finish laid. I dug the hole for the 1st bollard today which I knew had the mains power running nearby. Typically...

I purchased it new 2 years ago and have only just got round to setting it up so new. The POE switch recognises that it is drawings power and the AP lights up so i cant see the power as being the issue.

I hope this is the correct section to post in. I am trying to set up my Unifi6 AP. I have connected it to my switch and it powers up. After a rest it flashes blue then white then solid white as i understand it should. I then connect ia the Unifi app. It doesnt recognise the AP automatically...

Gave them a call and they came out the following day and replaced it FOC. Cracking service.

Cheers. To be honest I dont know if it has ever worked. Can I buy a "entryphone london" handset and connect or would I need to get them in to do it?

This is the main panel. There is a company online also called entryphone so I will call them on Monday and see if this is one of theirs. If there is a way to wire up a new one that would be prefered over calling out an engineer.

It certainly looks cheap and is unbranded. I don't mind buying a new handset I just want to know I will be able to connect it.