Search results

Hi I am having a problem with resistance in the motor shaft of a riello 40 burner which is causing the burner to lock out and not restart after running for 30 minutes or so. I have replaced the oil pump and the motor bearings but the problem is still there. There is also a medium level warbling...

Hi I have a very noisy extractor fan in a neff cooker hood. Photo attached . Is it possible to replace this fan with a much quieter version? Thanks

Riello 40 burner - 10 years old My burner has been making a noise for a few months now and has cut out sporadically in recent times. I have checked all the normal items when servicing and everything seems to be in order. The noise is like low level grinding, starts slow when the boiler starts...

I would like to replace the kitchen unit doors in an apartment kitchen as shown in the photos. The kitchen is in good condition except for the wrapping on the door (mdf with vinyl wrap). I don't want to go to the unnecessary expense of replacing the entire kitchen but have been unable to get a...

Hi Can anyone please advise on the fixed door fixings that I require and where I can get them online for a bosch undercounter integrated fridge Thanks

Gerkros thermostat not operating on domestic boiler. Boiler working ok but not cutting out at set temperature. Can a like for like replacement be purchased or can the thermostat be repaired? I have done a quick search online but can't see a similar thermostat

My Dyson v6 vacuum has been operating intermittently for the past couple of weeks. Basically, when fully charged it operates for about 1 minute and then cuts out. When placed back onto the charger for about 30 seconds it operates again for about 3 minutes and then cuts out again and so on. I...

Hi My domestic dehumidifier (9 months old) stopped working and is showing 'P1' in the digital display. Does anyone know what this means? I emailed Kaz, the warranty provider, and I have not yet received a reply Thanks

Hi I have a Bosch Exxcel 1400 S Express washing machine which has recently been giving problems . Basically, a wash cycle is repeated twice automatically before finishing. The cycle goes through to 1 minute left and then jumps to the start of the cycle again. After the second time around for the...

My Indesit dishwasher has recently developed a fault......on cycle 3 the dishwasher fills and begins to wash, after about 20 minutes 2 green lights begin to flash and the cycle stops. Can anyone suggest what is causing the fault? Thanks

Redring slimline 650 electric shower Shower stopped working during use. Basically the 4 control buttons to the front of the unit, top 2 there is no red light coming on and nothing else happening when they are pressed, bottom 2 red light is coming on when pressed but nothing else happening...

Shower stopped working while it was on. The top two setting lights do not illuminate when the buttons are pressed. The third down comes on when the button is pushed but nothing happens, no sound, no flow. The light on the bottom 'off' button flashes as normal when pressed. Grateful if anyone...

I just installed a new switch for the electric shower and the red light indicator in permanently on, even when the switch is in the off position. Checked wiring and it seems fine. Maybe it's normal with this particular switch, can't see a make on the casing. Can anyone confirm that it is normal...

I have a redring electric shower which blows the 30amp fuse everytime its used. Just started to do this over the past few days. Seems to last a bit longer if the shower water temperature is kept a bit lower. Have looked inside and wiring, etc. appears ok. See pictures. Grateful for any advice on...

I have a redring electric shower, model no. 53-558202, which has suddenly stopped operating, approx. 5 years old There are 4 red indicator lights and buttons on the front panel, 3 for different heat settings and the fourth for turning off. The low heat indicator light works, as does the off...

Hi, grateful for some guidance on a problem with a bosch exxcel 1400 wm. Set machine to any setting and it immediately starts pump to drain machine. When drain cycle is complete the wm stops and the digital display indicates that the programme is finished by displaying -0- Any ideas? thanks