Search results

Could i cut off the croc. clips off the charger, and fit a ciggy lighter plug? the socket is always on, even when engine is off & key out ignition.

Hi all. My TV is 4 years old. I tried retuning due to the bilsdale transmitter being worked on. I tried to do a factory reset but kept showing the channel it was on. When I did a retune, all channels were lost and on another attempt , all the channels were mixed up.. eg I selected bbc 2 and got...

Hi all, Firstly, After storm Arwen, a couple of tiles were damaged by uplift. 18 inch square hardrow slates "half tiles" on the edge so 18x9 inch. I only had 1 spare so would it be ok to leave the other in place? Sorry I thought I had a pic, it's more 9x9 and the bottom edge is flush with the...

Changed the plugs, on my 59 plate only to find a fair amount of oil pooling next to number 3 and 4 spark plug. I changed the plugs and fitted new HT leads , silicon grease on spark plug end boots with cotton bud careful not to touch the connector but didnt do the boots at coil end as silicon...

a mechanic, said the lid on my fiesta zetec was tight, he took it off and squirted lots of WD40 on the inside of the lid, before screwing it back on. I drove it 3 miles home, then rubbed it all off. I looked into the coolant fluid but couldn't tell if any dripped into the coolant. The wd40 left...

After looking into replaccing the oven element I discovered there's another element that looks similar to the grill one, but located underneath the oven.. If it blows would it be necessary to replace it or could I leave it?

Hello All, Daft question here.. After injecting Sentinel into an indirect heating system, would it be worth draining some water from the header tank up in the loft afterwards? (I was thinking of excess pressure on the ball cock valve by the float) I realise the level wouldn't go up much with...

Is it and other makes effective?

Is jetwashing the best way to clean it or is products like wetandforget a goog alternative? Ive jetwashed before and hard work plus some blocks are wearing away

I can't get an exact replacement. Would a different remote for linsar tv work?

I have a Neff oven, model B1GCCOAN0B I can find the oven if i Google the number, but get a "model not found!" when trying to find parts. What am I going wrong?

I've seen another thread on here, but wired differently to mine. I have 4 cables running into the Randall 3020P control box. The wiring into the terminals as follows : 1 = empty 2 = x1 red 3 = x2 neutral (1 black, 1 brown) 4= 1 black 5= empty 6= x2 brown 7 = x3 blue Earth = x3 green&yellow...

I have been decorating for my elderly mother who has glass panel doors. Glass is 27 x 32cm panels. 10 in each door. One door has 3 panels, 50 x 58cm. The doors have no removable beading, doors built around glass. Its not safety glass, so, before replacing the doors, is there a plastic...

Is there any glue i should use? Its thw rubber seal on the front edge of the rear door

Can spark plugs damage engines? Someone told me that the tips of irridium plugs can fall off and bugger the engine

I have ben told by a garage (croxdales) that the exhaust section from manifold to the cat is blowing and needs replacing at £600 plus fitting. I've been told that a specialist exhaust place could fix it for about £100. A place in Shiremoor, 20 miles from me the exhaust doctor, or a place in...

Ive been reading user feedback on Amazon etc.. Where the fabric type gloves didn't fully protect the wearer. Would chain mail gloves resist utility blades better?

The boxing gets damp from the condensation off the pipe and toilet cistern. The wood looks OK besides being tarnished. Is there any wood sealant i could use before paintin? ( I intend to use water based paint) or would plastic covering do a better job?

Its appprox 1/3 inch wide, 4 inches deep. At each side, this also runs about 4 inches under the wall at each side. Ive cleared the gap out, and can see the edge of damp course protruding 1/16th of an ich from under the concrete floor at or near the bottom of the hole . What would the best...

Apologies for creating a new thread, I ned some advice and time is short. My neighbour is a mechanic and said he'd fix the problem. Been off the road 2 weeks now and still not sorted due to dispute with the supplier he used regarding correct part etc. In the meantime I lost my job...