Search results

Installed alarm a few weeks ago, after a few teething problems got it all working with no problems. But after approx 4 weeks of it working OK I have a zone that keeps setting the alarm off on the tamper circuit, it's wired as EOL as all the others zones, why is this happening? Could it be dodgy...

Can anyone recommend a decent wireless room stat, ideally I would like to be able to monitor it and make adjustments remotely using my laptop / iphone4?

Just connected 2 smoke alarms and wired them into the premier 24 expander, configured zones and all works ok. I have configured output 1 on speech dialler for fire warning message. Run test on unit and all works well. I have set fire zones onto user test, run test and all works well. Removed...

Managed to get everything working ok, I have set the channel to 52 on the modulator and get good quality pictures from 3 of our 4 TV's. The main TV in the lounge however will not tune in to the CCTV Chanell. Also the kitchen TV has tuned in and is showing good quality CCTV, however on this TV...

Started my new project installing a CCTV system, setting up the cameras & DVR seems reasonably OK not tried the LAN stuff yet, I am tackling one problem at atime. Now the system is working on a monitor, I now want to try and send the CCTV pictures to all the TV's in the house. What I have...

Finally got everything working OK, on a separate note is it possible to programme comms 2 or 4 to send a voice & text message when mains power fails, this happened yesterday, the alarm is fed via a 3 amp RCD which tripped via the main breaker which also tripped ring main feeding fridge...

I want to purchase a CCTV system for home use I intend to install myself, can anyone recommend which one is the best, I am going to fit 4 outside cameras and 2/3 inside. I would like purchase the DVR separately and then add the cameras, for the DVR I am thinking Swann, K Guard, Vanguard but...

Thinking about my next project which is to install a 8 channel cctv system I can't decide whether to buy a hard wired KGuard system or Swann, I don't want to spend a fortune but I do want a decent system. Initially I am planning to install 4 outside camera's and 2 inside cameras. I would...

Finally got the speech dialler configured and the tests mode works fine, I even receive text messages. When I arm the alarm I get a phone call telling me the alarm has been activated? which is the message I configured for alarm activated. When I set the alarm off the speech dialler does...

Every time I try to configure my speech dialler, about halfway through the programming and testing the unit locks up, it will not allow me to enter the pass-code it just does nothing. I have removed power from it and reset it it a number of times but the same thing keeps happening. Could it be...

I have just installed my Premier 24 Alarm and finally got it all working, I have spent ages setting up all the configurations and entering text, but it all works. However I have a problem with the speech dialler which I now need to configure this problem has now happened a couple of times. I...

Finally got my system working, can I thank everyone who gave me advice I wouldn't have done it without you. Having problems with speech dialer sending text messages, but after a bit of research I see that this is not uncommon, I have quite a few suggestions to follow up on. I receive phone...

I have finished all the wiring of my Premier 24 with 11 PIR wired (EOL) expander, 2 keypads and speech dialer. I have managed to remove ALL alerts on the keypad, Bell Tamper, & Auxiliary Tamper. I have done a walk test ALL OK I have done a bell test ALL OK The problem I now have is...

I have just wired in my Premier 24 - which has 11 PIR wired (EOL), 2 keypads, 1 zone expander, 1 speach dialler. when I powered up everything appeared OK, I have done a walk test and all the zones worked. However I have 2 faults 1 Auxilliary tamper circuit fault ( I have connected the...

Can someone give me advice on how to wire the texecom speech dialler into the premier 24 control panel. I assume 0v 12v are power connection Tamper wires into the control panel tamper circuit, which is not used (EOL wiring) I am OK with the phone connection But I am struggling with...

I have wired in alarms before but I have not done EOL I think I understand it but can someone tell me if what I am doing is correct I have PIR with jumpers which can be set for EOL resistance, which I have set. So do I now but one wire into the alarm circuit (if so which terminal) do I...