Search results

I have just paid a (useless) plasterer/decorator to plaster and paint bedroom three in our house. Its the small box room and we are in our third week, it has been painted but the snagging list is enormous. Lots of blisters, patchy paint, trowel marks, craters... Anyway things have escalated to...

We have moved into house which has an open fireplace. There is no mantel piece but a square recess in the chimney breast with tiled floor and a flue! We would like to install a small multi-fuel stove to supplement the central heating, as the house is rented we are looking if it is possible to...

Hi, I am looking at getting an unvented direct system fitted to a ground floor flat of mine. The hot water pressure is hopeless and the only means of heating is electric so I thing this type of system would be best.. I know there are a number of manufacturers of these systems - Megaflow...

I use a barn as some workshop space. Its probably 120 years old and the floor in one corner is particularly un-even. It looks to be a load of red bricks which is quite broken up. There is quite a bit of soil which I am drying out so I can hopefully sweep away and see if it is an old floor or...

I need to build a stud wall. I do not have the measurement to hand (I'm at work), but it is not divisible by 400mm. Is it best to do either end and the middle or should I try and use 400mm centres and a random remainder?

Hi, I am planning on re-tiling our bathroom. What is the best way of finishing where the wall tile meets the ceiling? At present the tiles stop, there is an inch of emulsion/plaster wall. Then coving and the ceiling....It looks nasty

I am planning a bathroom refit and one of the jobs is to install a wall mounted extractor. The bathroom is quite small and the fan will be mounted to the wall over the bath (opposite end to the shower head). It it acceptable to have the isolator and fused spur outside of the bathroom or...

Hi, bit new to this so bear with me.... I am looking to build false wall and tile over in my bathroom. The two areas in particular are the end of the bath/shower and an alcove next to the washbasin. I have read recommendations for Aquapanel, Hardiebacker or BAL WP1 and know to steer clear...

I am changing our bathroom around... At present there is a surface mounted bar mixer for the shower. This is fed by two vertical pipes. I am wanting to re-tile the room and would like to channel the walls out and tile over the top. what is the best way of doing this? The walls are breeze...

I have a flat which is fitted with DG panes in timber frames. A couple of the original cockspur latches have failed and require replacing/have been replaced with poorly made latches. Can anyone suggest a supplier of a sturdy latch that is reasonable to look at suitable for a timber window...

I have installed a salamander ESP75 CPV pump to a Gledhill Envirofoam Stainless Steel SE36X18IND Hot Water Water Cylinder. The cold feed I have taken from the CWS via 22mm pipe. The hot is from the shower take off point (similar to essex flange) which is fitted as std. to the cylinder. It...

I have investigated the back of my Gledhill cylinder and conveniently enough there is a factory installed power shower take off. I need to attach a 22mm fitting (I assume 3/4BSP) to it. However there is very little space between the shower take off and the back of my airing cupboard. I can...

I have: 25 Gallon Cold Water Storage Tank 25 Gallon Hot Water Cylinder 6" Negative Head Salamander ESP 75 CPV Shower pump: Type – 2.2 bar twin-ended two stage centrifugal Maximum Pressure – 2.2 bar Duty point 1 – 2.1 bar at 10 litres/min Duty point 2 – 1.95 bar at 20 litres/min...

I am shortly going to fit a salamander ESP 75 CPV shower pump and Bristan thermostatic shower unit. I live in a flat and I have a negative head situation (this pump should be good for that). I intend running a dedicated 22mm copper pipe from the cold water tank to the pump (no worries). I...