Search results

  1. F

    Ideal Classic Flow Rate & Grundfos pump

    Hi All, My parents have a Ideal Classic RS360 boiler with a Grundfos 15-60 130 pump. The pump is currently under the floor and set to position “III” - I was trying to make sense of the flowrates and pump data to see if a lower setting might be suitable...22.9 l/min would be about 0.38 l/sec...
  2. F

    Danfoss Fridge/Freezer Thernostat query...

    Hello all, Looking to replace a Danfoss 077B6635 which I seem to be struggling to find...I can see similar ones 077Bnnnn but wonder what the difference might be ? Just wondering if it's more a physical thing in so much as the capillary length rather than the actual thermostat and I could take...
  3. F

    Ideal RS330 and cool radiators....any help appreciated

    Back at my parents to try and sort out “Cold/Cool” radiators downstairs...well trodden ground I know, sorry ! Basic Semi; Ideal RS330 boiler – all radiators on one zone, 4 upstairs (2 small) and 3 downstairs so nothing really that should cause issues. Upstairs all hot, downstairs all pretty...
  4. F

    Old Boss Therm BZV22...trying to find one..

    Bit of a long shot...don't suppose anybody has, or knows of any of these “old” Boss Therm (BZV22) 2 Port 22mm valves gathering dust by chance, trying to get hold of one seems a tall order ? Needing to replace one for a relative as the plastic gearing has worn so it doesn't open completely...
  5. F

    Best/Suggested fixings for steel plate/post to concrete footings ?

    Hi All, Looking to fit a new hardwood driveway gate to be hung off a new stone pillar - yet to be finished but new walling in progress. Going to add add strength to pillar by putting a steel box section post on a plate and fix to footings and building pillar around and fill cavity. Any...
  6. F

    Independent C30: Flow Turbine – Turbine Sensor - Diverter Valve or ?

    Hi All, We seem to have lost our DHW from our C30 this evening. Hasn't been an issue before. With CH burner ignites as required and all seems OK but we have no DHW - Burner just doesn't ignite. Can't see any LED flashing or illuminated on top of the sensor when hot water taps turned on so...
  7. F

    Help with BOSS/Siemans 2 Port Motor/Actuator

    Hi All, Am trying to locate a Motor/Actuator that might fit my parents 2 port CH valve.... It is going back a few years and my Dad has already replaced the gears at some pint in the past as he has a couple of “cannibalised” units as per the pictures below. Units are PTS branded BOSS BZV22 but...
  8. F

    Satchwell CH/HW Timer...

    My parents have what you would probably call a vintage Satchwell Central Heating & Hot Water Timer (as per attached picture) It has 12 available time settings throughput the 24Hr period for CH / HW. It has, as far as I am aware worked without an issue for a good number of years. They have been...
  9. F

    AEG Lavatherm 620 DREEFS Switch (Vintage !)

    Hi All, Parents Lavatherm 620 Dryer has stopped working - Power On/Off suddenly became Intermittent then stopped completely. I have remove the Button/Switch pack from the front which appears to be a DREEFS unit - four push buttons plus one illuminated. The On/Off switch seems to have failed -...
  10. F

    Adhesive for a laminate strip.......??

    Morning All, Recently purchased property that has been redecorated throughout although we have kept the laminate floor (Pergo) in one room....I have removed the original Skirting board though as new CH pipes have been fitted and hidden at the base of the wall. I now have a gap of around 25mm...
  11. F

    M3.5 Screws x 50/75mm...flat headed

    Hi All, Wondering if anybody might know of a source for longer plug/socket machine screws...looking for flat headed, slotted and at least 50mm...most seem to be raised / domed slightly and I would like them to fit flush. I've tried out local outlets for fasteners and electrical stuff to no...
  12. F

    T&E in Safe Zone – To trunk or not to trunk....

    Evening All, I have a couple of Power and lighting Cables going up a new chase in plaster board on a external wall to the loft...it's around 125mm from the corner of an adjoining internal wall so a Safe Zone. Original plan was to put some plastic trunking up (behind it) to run it in and then...
  13. F

    Help/suggestions with External Light or Junction box...

    Hopefully somebody might be able to make sense of my waffle..... New house (to us)...we have an external wall light outside the kitchen door – it is on the downstairs lighting circuit and the first point of call from the consumer unit for the Live feed. Originally this must have had a switched...
  14. F

    Quick Fused Connection Unit query on a spur....

    Quick query please guys... I have a Spur coming off a Ring Main (Junction Box). This supplies a Switched, fused connection Unit which itself supplies a Alarm panel under some stairs. I'm wanting to put a light source (2ft 18W Tube) in there with this Spur being the only real option. Can I tag...
  15. F

    Skirting Adhesive Help/Advice please...

    Hi All, Not sure if this would be best here or in “Decorating” but any insight/help would be much appreciated, thanks in advance .... We have had a new conservatory added – Quick Step laminate flooring has gone down in there and we have matching Quick Step Parquet Skirting (77x14mm) to go with...
  16. F

    Fused Spur - location...can it be "hidden"...??

    Hi All, About to start looking for info but quick query please on location of a fused spur or single socket for use as a connection for a couple of fire surround downlights.... ..looking to add two low voltage down lights to a timber fire surround. I have a one single socket on downstairs...
  17. F

    Another "Replace Microbore" Type post......

    Hi All, Thanks in advance for your time...any input would be appreciated, Our house currently has an Independent C30 Combi feeding 8 radiators (4 down, 4 up) – concrete base so all off downstairs fed by droppers. Feed and return from/to Boiler is 22mm is via two “manifolds” upstairs that have...
  18. F

    Euro Cyilnder removal assistance....

    Hi all I've been trying to help a friend in changing her basic Euro Cylinder to a more secure Anti Snap variants. The front door no problem - old one out; new one in. The back door I'm struggging with. Removed the Cylinder locking screw but something is stopping the cylinder sliding...
Back
Top