Search results

Hi, I have a Behringer FCA610 that is making a humming noise and flashing the lights when you power it up, I have taken the front board off and it is still humming, I was wondering if anyone has experienced this before? I am suspecting the transformer on the PCB or possibly a cap thats failed...

Hi, I have a g2-20 panel installed and working fine until 2 nights ago, at about 4pm (14/11) 2 panic buttons leds started flickering red as if they had been pressed and the mk7 by the door has no display but the green led at the bottom is on, the panel is not in an alarm state or reporting any...

Hi, I'm having a problem with one of my keyprox modules (address 1), when I went out earlier on I used it to full set via pin number, when I came home again it wouldn't respond to a fob to unset or accept a pin, subsequently the alarm triggered and had to be unset from a second keypad (address...

Hi all, I recently posted a question asking about a 24h contact with override key switch (http://tinyurl.com/jdtyw6f) I have installed the zone with the key switch to shunt the contact with so the gate can be opened without the alarm activating, however I am now getting an open signal from the...

Hi, Hope someone can help, I recently bought an Avaya 1140e running SIP04.04.14.00 and need to downgrade it to SIP1140e02.02.21.00 so it can register on my PBX system, I can get it to communicate through the TFTP server and it takes the .cfg file but it wont take the .bin file and update, does...

Hi all, Just wondering if anyone could help me to figure out how to use a 24 hour zone on my Galaxy G2-20 whilst maintaining the ability to deactivate the zone when required? I have seen this done in a company I used to work for where the fire doors where monitored for breaches but one door...

Hi all, after perusing the forum and reading one article on the installation of the max3, I have followed the cabling and install as per the post and confirmed it with the install sheet that came with my reader, but I still can't get the reader to set and unset the system when presented with a...

Hi Everyone, I was just wondering if anyone could tell me how I wire 2 devices onto one zone on my G2-20? I would never normally but as it is not for an intruder zone just a fire zone, and I only have 1 zone free which has been earmarked for another device, and I just can't seem to figure it...

Hi everyone, I own a PRM 10 projector made by Promethean that used to work fine, but when I was mounting it to the ceiling I got an electric shock from the light fitting (which has since been removed) and dropped the projector from a height of approximately 3ft, it instantly powered off and...

Hi, a while back I asked a question about a hipath 540 PBX system, I finally got round to looking at it and it's working and all set up, I got the IP address sorted but for some reason I cant connect to the manager software, I have found a copy of hipath manager C, when I try to connect through...

Hi, I've got a G2-20, that I need to default and I've tried the suggestion form another post thread on here I have the old user code and have reset that to default but no engineer code, can anyone suggest another way of doing it? Thanks, JJ

Hi, I have a Micros Workstation 4 system and I cant get it to boot, I have no idea how they work, operate or boot. I was wondering if anyone has had any experience with these systems, do they require a HDD or are they slave systems that run over a network setting? If anyone could help me to get...

Hi, I installed a g2-20 earlier this year but due to unforeseen issues I have had to move to control panel, labelled all the connections and replaced a run of cable, wired it all back in exactly as it came out but the problem I have now is when I apply power the auxiliary power fuse blows and...

Hi, I currently own a Siemens hipath 540 PBX and 4 optipoint 500 phones (2 standard, 2 basic (RJ45 plugs)) and I was wondering, well, kind of desperately hoping someone could help me in installing the system to a fully functioning state, ready to plug the ISDN2 lines in when they are...

Hi, I'm currently wiring an exit termination button to my G2-20, the button is normally open and wired with a 1K resistor over the contacts and a second 1K back to the panel (drawing below) as a zone would be wired, when I do this it sets immediately without the button being touched, all the...

Hi, just wiring my Galaxy G2 with a third rio for the level and was wondering if it is possible to wire a roshni or two onto the rio outputs and set them to only activate on a smoke detector alarm Thanks in advance - Josh

Hi, I've recently bought a Siemens hipath 540 pbx with 4 optipoint 500 handsets, and was just wondering if anyone has had experience wiring and setting one up, as no installation guide was with it and I cant seem to find any online. Thanks for all your help in advance J