Search results

Anyone have hands on experience with Wallrock Thermal Liner? £50 a roll 10m x 0.75m It's pop to hang. http://www.youtube.com/watch?v=T9Q072gox7I I'm not convinced, might aswell carpet the wall.

In the back of my mind was the thought that for it to be of any use it might need to have air or a cavity behind it. I figure if I vent behind the cavity, that should remove any chance of condensation build up. If they can place that foam stuff on a wall then I think that there...

Surely the way to go is a suspended ceiling.

That's something I have no knowledge about, sorry. It's in a stairwell which is always very cold, especialy now winter is here. I will be using a water resistant adhesive, no idea which one at the moment. And then sealing it with the same, then hanging the lining paper over the...

With a decent adhesive, and lining paper over the top. I cannot see it rotting away. Sandwiched between adhesive it has no where to go. All it has to do is reflect the heat back.

Aluminized mylar space blankets. Mylar sheet installed internally with an aluminized coating on the side facing you. Possibly 1200 grade lining paper first(or god forbid polystyrene) and finished with 1200 paper. (Really do not fancy any polystyrene. Too easily damaged.) Anyone ever tried...

Read through the manual downloaded from Biasi, found the reset switch from where it overheats. Pressed and bingo! FIXED ! :) cheers for all your help.

After taking it apart, I see the spindle that runs through to the opposite end to push the micro switch - is only moving about 1/4 inch. It will not move any further so it's about an 1/8 inch away from hitting the switch. After seeing the condition of the old diaphragm, I am pondering the...

After looking at the biasi blown diagram for that valve, the diaphragm is installed the correct way round.

Yep that clear switch is not working, the pin ** spindle ** is not moving. o/ht? Sorry, no idea what this is. water pressure is being set at 1bar

That pin is not making the switch. Has not fired up since changed the part, just makes a buzzing sound for a while which quietens after a minute or so. Pump running as can hear the water moving in the radiators. C/H was not working, H/W either. Was left for quite a while with...

Maybe this will help, as I don't know the actual names of the parts.

He fitted the new rubber diaphragm so it was snug , parallel to the left side. This could be the problem then. I will drain down and strip that part off again. Waiting for confirmation before I reverse it. (No heating or h/water. Pump running) Cheers guys, really appreciate you...

None of those things have been checked. I am there now, and unfortunately neither of us know much about boilers, so not sure where the switch and fan are that you mention. Pump is running. I see one pin pushing into the switch that is nearest the left. The other switch/pin is hidden by the...

bump

Anyone have some ideas what to test next? This is be my brother, I told him this was the place to get help ;) Cheers guys!

Cheers legs-akimbo, I'm going to use your advice with the mix, and also the beads around winows and door, using just a batten to render up to for my edges. Thanks for your time and knowledge, very much appreciated.

Thanks for the link. They don't mention lime...is it ok to put lime in with the waterproofer? Well, I spose I'll find out, I'll put 3:1:1 scratch with a splash of watewrproofer. 4:1:1 +waterproofer final coat. And have fingers crossed and hope for the best. Cheers for all your help guys!

I can't find any info on waterproofer quantity..just a cap of per mix? Going to use a cement mixer from hire shop. Also I just read that the lime should be soaked in water for 24 hours?. The more I look into this the more there is to know. I've got to do this job for my dad as the house...

ok guys thanks for your advice. I asked the builders merchant for exterior beads, but the bellcast and the angle beads both looked galvanised to me. They never mentioned stainless or plastic. Hope galanised will suffice. Legs, belive me I've searched, the most info was this site...