Search results

Hi guys i have a worn keypad. There are two types of 9427. Are they interchangeable? or another option ? if anyone has the blue one in old stock id be happy to do a deal.. thanks in advance.

Hi guys, anyone know how to remove the black tape that comes with the skylight glass frames? i want to remove it for a clean perimeter, and get the glue off. image attached. any advice from glaziers would be appreciated.

Hi, can someone advise me please? I am having building work done, and need to disable or remove a PIR for a period. I thought I could enter eng mode and remove the pir to a different location but the code doesnt seem to work (no lights flash). I tried to remove the cover but the tamper switch...

hi, Anyone know what the model in the attachment is? I thought it was a 1901 but doesnt have the raised front on it behind the bezel. I'm trying to get to the valve but cannot get the handle to budge. If i remove the ceramic part by unscrewing the cap, there is a long threaded screw, but it...

Hi, I recently ordered these tiles from an online warehouse that said they were in stock, took my order and money. Now a week later and no delivery I have on calling been told they are out of stock for 5 weeks at least. :evil: Does anyone know where I can buy Delta Vanilla 60cm x...

Hi all, i have finally bitten the bullet and dug up a failed screed floor in a kitchen which i need to get ready to tile. I'm going to put 60cm x 60cm large format tiles down so floor has to be spot on, and it has to match level with adjacent room that will be part of expanded kitchen...

Hi, I looked at plenty of trowel questions, and most end up saying use a 20mm/10mm round for floors. BAL say use 20mm/13mm round for large format tiles. Is that really necessary? and if so where can that be sourced? I cant find one anywhere having trolled the web for a couple of...

Hi guys, my alarm started blaring at1am last night, and after a lot of fiddling and removing of power, the bell eventually drained itself flat. i have identified the problem with the AC and battery. Does, any one on here have any information about where i could buy a transformer for the...

Hi All, I have just laid a Travertine floor, and know that I have to seal it before I grout, and then clean, and re-seal when the grouts dry. Can someone please advise me what products to buy to do this with? I'm going to be doing the walls as well, so will need sufficient amount to...

Hi, My old FF has developed a fault with the fridge part. It wont cool at all, yet the freezer is fine. Unit has been defrosted for some time, and when i turned it back on the freezer cooled down within an hour or so. The fridge part is not cool at all. The fins on the back are vey warm...

Hi, i'm in the process of renewing my old kitchen. Floors , walls, cabinets and white goods. First up is the floor. The floor is 70% screed, 30% wooden suspended. I have removed the floor boards and installed noggins between the joists, overlaid with 18mm ply and screwed down...

Hi, have a 758 that the lower oven will not remain lit. I have checked the TC is in the flame, but as soon as you let go of the oven knob out goes the flame. I will get the TC replaced, but can anyone tell me if the other TC fitted to the top side of the lower oven space also should be...

Hi everyone Have a Whirlpool AWD049 that consitently takes in the conditioner with the wash cycle and not the rinse cycle. Whirlpool have looked at it and said that the problem is too much water pressure but this has been turned down to around 2-3 Bar. Problem remains, and its...

Hi Anyone out there that can advise me on block paver pattern? I want to have a 105 x 140 single size block pavers installed on my entire driveway set in a strecher bond, offset joints etc, with a 3 course border in 3 sizes. Is there any issue doing this with strength etc? I'm being...

Hi My mum has an old flat and the kitchen light cable is the old lead coated sleeve with two wires. As there is no earth wire, is it practice to use the sleeve as earth, attaching a wire to that, or if not , should a plastic light fitting be used? Its a ground floor flat so replacing the...

I have a Whirlpool ARG917 intergrated f/f. Its working fine in the lower freezer part, however the top fridge part has a problem. The top half of the fridge is iced up, the lower half is ice free, and the back wall is warm to the touch in that area. I,m wondering what the problem could...

Hi all, Have a CSI85t thats developed a strange problem. When the heating is OFF and set to SUMMER ie HW only, the boiler fires up fine when a tap is turned on and hot water is drawn, BUT the radiators get hot. This happens whether or not the switch is set to HW only or CH and HW...

Hi I have a PC thats got a blown power supply. Ive had a look and tried to repair it, but its smoked so I need a new one. Model is FSP250-60 GTV (PF) Its made by FSP in Taiwan and used mainly in the home user market. Does anyone know where I can get a replacement or if theres a...

Im going to be replacing my Potterton Lynx this summer after 18 glorious years (apart from the last few weeks and the gas board but thats another story) I'm considering the Alpha CD50 because I like the idea of a water store without the attic tank. I have 1 bath and two showers plus the...

Can anyone tell me if the air flow switch in the potterton Lynx, (not lynx 2) can be substituted for the one in the Lynx 2. The part number for the original is 300303, and for the Lynx2 642218. I am having trouble finding a spare of the original, and wondered if the latter could be...