Search results

Every time i set the alarm the Bell box and sounder beep twice (not good for the neighbours) if i do part silent no noise. any ideas anyone

Hi, I have a magnet on the door zone1 set to final. Should the pir in the hall, zone2, overlooking the the door and keypad be set set to Exit or Entry? Thanks in advance. Jeramy

Hi i have just updated my Flex 100 firmware and have reprogramed the rf zones and hopefully everything else. But its thrown up an "aux tamp 004" error. Any ideas on how to remedy it. Thanks in advance, Jeramy

Hi, I have an error message "comm fail rec. 4" on my keypad. I installed the alarm and it is connected to the internet for push notifications and that works fine. Anyone got an ideas about this? I take it the rec. 4 is short for receiver 4? So maybe i've miss programmed something in the...

I have the above fob intalled on my Flex 100 alarm. When I activate the PA buttons all I get is the internal speaker ringing OP3. I want the bells as well. Is there a way I can put a wire between OP3 and the bell box to get them both to ring at the same time? Thanks for your responses in advance.

Hi, I have a Flex panel with 2 keypads wired to the RS485 Bus. I have fitted 680 ohm resistors on each keypad and removed the jumper at the bus. I want to add C079-2 RF Module so that would be a third set of wires coming from the bus. Do I need to add another EOL resistor? Thanks for your help...

Please could somebody verify I got this right. On keypad menu 21 display zones. For my RF zone I get Sig 10 low 08. I take sig is current signal which is "excelent" Low refers to the lowest it has ever been? Meaning 10 excelent and 0 crap?

Hi, I have installed my first wireless le sucre PIR on my flex system. Everything went ok with pairing until next morning I get keypad message rf batlow. Result: I am on my 3rd battery in 3 days!! Has anybody had this problem? Many thanks,

Hi, here is my problem. I night set or silent part set my flex alarm on going to bed to stop beeps from internal sounder (OP3 on board). In the morning when I get up and use the app on phone to unset I get the final two unset beeps from the internal sounder which is not ideal if others are...

Hi, I have a flex alarm panel. I would like to wire this sensor up to a zone but i am not sure what terminals on the panel to use. Any guidance would be appreciated. Thanks Jeramy,

Hi, I have a flex system and am looking to install a wireless shock sensor. Before I buy one Does anybody know how these are fitted to the window frame as i dont want to drill holes in my aluminium frames. Will double sided tape be ok? Many thanks for responding. Jeramy

Hi, I have just got my hands on Honeywell RF Portal A073-00-01. In the flex maual it shows it comes with a directional antenna but mine came with out one. Does this mean it mean I am missing one or is it built in? Many thanks in advance. Jeramy

Hi, I have a galaxy flex which I'm trying to install myself!!! It says in manual that needs a 680ohm end of line resistor on the end of the bus. Then later on it shows a sketch that i need two resistors. One at the panel this time and one at EOL. Q.1 Do I need to put 2 resistors only if I have...

Hi, I have a galaxy flex and want to add a wireless pir. What module do I need to get to do this. I see on Honeywell's website they have a C072 Galaxy RIO - 8 inputs/4 outputs and a A073-00-01 Direct mount RF portal PCB. I assum I need one of these. Can somebody give short explanation on what is...

Hi, Please can somebody give me some direction on wiring this dialer to an Accenta G4 mini panel. I want to be notified when the bell goes off and to be able to reset alarm system remotely. Also do i need to install a relay? Thanks in advance, Jeramy