Search results

got a brick shed in my garden with a concrete roof,that leaks what is the best stuff to paint on the roof to make it watertight? was lookin at rubberised bitumen emulsion ? any advice would be great thanks

anyone got any its to light a kitchen :? just wana make sure there not going to be dull and waste money

putting six sunken 50w spotlights in my kitchen ceiling. took me ages to mark the area out so they was even etc. my new problem is in 2 ov the holes theres wires around where the lights have to go. but not directly abouve the lights. is there anything i can do as i do NOT fancy markin out all...

are they any good ? or somet i should steer well clear ov :oops: any input would be very much appreciated :wink:

enclosed a pic ov where i want to run the cable in pvc conduit. is it possible ? only reason i ask is because i dont want to try run it thru the house,under the stairs thru 2 walls and along the kitchen wall. also i cant bury it along my ginnell as my neighbour wont allowe me to lift the flags...

i`m putting down some driveway drainage but i`m not sure what size the clay pipe is, i`ve enclosed a pic and in the pick is some pvc pipe 110mm. as you can see i`m restricted and cant use a trap. i was hoping to use a strap boss but that does`nt look feasable or maybe a clay saddle but its...

my problem is how can i tell if my waste pipe is surface source or foul source as i`m gonna have trouble putting a trap in. i`ve enclosed a picture ov where the drainage is goin roughly one brick below the DPC any help would be great

is it possible to run a cable from my existing outside light with PVC Conduit to my brick shed with a concrete roof ? the shed roof has been waterproofed etc. and also my main consumer unit is at the front ov the house and would be an utter pain to install a Garage Consumer Unit i`ve enclosed...

is it possible to drill thru the posts below. reason being i cant sink the post in the ground and concrete it in. due to a gas pipe about 2 ft down directly below where i want to stick the post. my only option is to drill the post and either screw it or bolt it to the wall. pipe...

a few years ago i was artexing the backroom ceiling. i did the ceiling at night as to avoid the kids running around (big mistake) i finished about 2am and was a bit wacked to move everythin and clean what artex was left in the bucket,i`ll do that tomorrow i though. the next day i got the shock...

i was hammering a loose floorboard before fitting laminate flooring, and went straight thru the central heating pipe :? i was quite impressed with my accuracy tho smack in the centre ov the pipe :lol: i think i cleared under the sink in seconds to find the stop tap :lol:

can you use 16ge brads in an 18ge nail gun :?:

was thinking ov this for drainage :?: as i`m in the prosess of doing my driveway and the drive will be sloaping towards the house. i need roughly 10ft. can someone point me in the direction ov somewhere it can be bought from in the blackpool area and a rough idea ov cost :?

anyone know where i might be able to get some blackpool area

whats the diffrence etc brad finish 16 guage 18 guage dewalt do a nice range. just wondering what to look for or steer clear from i`d say it was for general woodworking diy

just wondering if i can get these removed otherwise i`m fooked as theres this chiney stack now unused blocking my route to the main part of the loft as you can see its the same the other side more pics can be supplied if you need to see more

it has 2 doors and a wall to seperate the shed with a concrete roof first section is the shed and the 2nd is a coal shed both have doors. i`m just wondering if i knock out the partitioning wall and brick up the coal shed door.will it be safe :? or would i be safer installing an RSJ :?:

fitting laminate flooring in my boys room this week. so beforehand i decided to nail down any lose or creaking floorboards. all went until i came to a slight lump on one ov the floorboards. and though to myself mmmmmm a nail should sort this little problem. no sooner had i hammerd the nail in i...

my daughter is complaining her little room where her clothers are hung is too dark. was thinking ov fitting a light. its not to far away from the switch. but ideally i wanted a 2 way switch so she can turn it off when its not being used. can anyone advise please. stuff i need etc and the easiest...