Search results

Does anyone no if there is a chart listing oil boiler manafactures and there nozzle sizes please. Brian

Hi all went to a house recently customer complained about constant pressure drop in central heating she has had two new rads fitted and the problem started from that point. No I didnt fit them the prv is ok there is no water showing from the pressure vessel no apparent water leaks Im...

Hi gentlemen Been a bit busy so I hav'nt been on for a while. A few weeks ago I asked for help on this boiler, locks out only when cold once its on it is fine. Telephoned Trianco they didn't have a clue. So far I have examined the oil pipe as it is all exposed apart from where it...

Hi Any ideas please, the burner cuts out after a few seconds then when you reset it, it fires ok? It has been serviced, new nozzle, smoke no:0-1, pump pressure to spec. Thanks Brian

Hi can you tell me what the regulations are for the height of rads above skirtings. I thought it was no less than 50mm, but I seem to remember reading that it has changed. Brian

Hello I am about to price to convert a semi pumped system, gravity fed to the cylinder to a fully pumped. As you probably know I am new to heating, so please correct me if I am wrong. Cut off and cap gravity fed side of boiler reconnect cut ends to pumped side via a controls pack...

Has anyone got the specifications on the Camray 2 please Nozzle sizes pump pressures etc. Thanks Brian

Hi all I am first fixing a three story house with three bathrooms. Will 15mm pipework for hot be ok or should it still be run in 22mm. My unvented course is not until september so I am not up on this type of system yet. Thanks Brian

Hi me again Can anyone tell me The best way to test the limit stat on oil boilers without endagering life and limb by taking the boiler to its limit temperature. Thanks Brian

Hi Apart from the usual possible problems with micro bore sludge build up etc, Can anyone advise me of any other problems I may come across when fitting a sealed system with 24 rads all in micro bore hep2o. Thanks Brian

Hi I have been asked to fit heating system in a large house approx 20 25 rads. the customer does not want pipes coming up from the floor, he would like them coming up behind the plasterboard wall then out horizontally to the rad valves. Would it be ok to run the main pipe work in 22mm then...

Hello In the Boulter MI's what are the flue distances in brackets please Thanks Im feeling a bit thick here by the way :oops: Brian

I am looking at a Thorn oil boiler ody3, with a Selectos burner D42 and a Suntec pump no numbers on it. Nozzle size is 85 x 80 presume solid Whats happening is the burner fires, a few seconds later the flame starts pulsing and smoking (Big time smoking) any guesses would be helpful pump...

Will all who post on here chill out. We answer your questions free of charge, despite the fact it has cost most of us thousands of pounds to become qualified. Yet you cant take a little bit of banter. If you cant handle it call a plumber and pay. :evil: Ok thats me done Happy again...

Just wanted to say thanks for the advice about swatting up for the Oft 600 it made the assement a lot easier. All done now for five years Best Regards Brian

hi can anyone tell me where is the best place to buy servicing and test equipment for domestic oil fired central heating units. need to know costs so that i can justify the oftec course Thanks Brian

hi I have just spoken to oftec insurance people they were quite willing to cover commercial work I said it would be about 10% of my work just guessed as you do got a general quote of 240.00 hope this helps Brian

anyone got a rough idea how much oft 101 and 105e costs for training and assesment. also if i do the 105 do i need the 600 thanks oil peoples I have mailed training centres but no replies yet so i thought i would ask you and help ease the shock brian

can you tell me the procedure for disposing of asbestos roofing sheets please any idea of cost single garage size. thanks Brian