Search results

Thanks for the info. Of course I agree with your thoughts above and never said you could learn a trade in 8 weeks. Just mentioned that the legal min was 8 weeks to gain qualification. As with karate, the real learning starts only when you achieve black belt status...that is not the...

Listen Tony, you are now going off at some tangent here, so much som I think that it's clear you have no wish to offer assistance. Your questions are becoming bizarre. Your assumptions wild. Just to pick one hole in what you say, I have never suggested 'free' training and even suggested that I...

Sorry Agile but re read my posts. I have not been aggressive or argumentative IMHO. I like to deal in facts and directly to the point. But if that's your interpretation so be it, you have perceived it that way. I have simply replied to your approach. Although I would probably say the same of...

Nothing wrong with that at all. So not sure what point (if any) you make here?

Thank you, I shall look int this. Sounds like the sort of expert knowledgeable advice I was hoping to find in the forum. Thanks. S

Thank you for the consideration but I would not wish to go into detail on this forum, save that for interviews! As for papers, I only read the sports pages at the back... S

Thanks for the reply Agile but please answer that yourself and educate me? Why? because as I am understand it a key element of gaining a proper education and certificates in the industry is to complete training under a mentor, min 8 weeks on the job training. I think that ALL trainees must do...

Hello all, I have decided to re-train as a gas safe engineer and wonder if there is a reputable training centre in the NW London/South Herts area that you have used and can recommend for a new trainee? I am based in Watford and can travel a reasonable distance. There are quite a few...

Thanks guys. I have it booked in at Nissan dealer service dept to look at tomorrow.

Hello all, I sadly hit a large pothole Tuesday night (aaaarrrggghhhh!). There was then this 'whirring' noise on impact like a spinning metal plate that gradually reduced in speed and stopped after about 5 secs never to be heard again. Front nearside wheel. Since then the steering has felt much...

It is def a 'physical whistle' as mute has no effect. If it continues and eventually causes a general picture/TV failure I shall go in search of a TV repairman first, rather than rush out to get a nice new 1080p HD ready flatscreen ! S

First time post in this section so greetings to all! Our 6 year old box is putting out some background noise apparently...I say apparently as my younger wife and 11 year old son complain regularly about it but my older ears can barely hear it at all! Im a bit deaf compared to them I guess...

Thanks to you both. I would not attempt anything complex or intricate that may risk injury or risk upsetting the safety feature itself! I just wondered if I had inadvertently pushed up into the bag when closing the overfull glove box. And if there was a way to 'undo' what I had done apart from...

Has anybody had any experience with their air bag warning lights? Any advise welcome. Thanks. Stephen

...and do make sure its topped up correctly as well (if not a sealed unit). S

...this has suddenly come on. Never seen it come on before in any vehicle Ive owned. However, I did have the glove box full of Cd's and 'stuff' and it jammed and would not close as I tried to shut it quite hard with a bit of a slam. Doh. Could this have 'upset' something in passenger airbag...

Seasons greeting s to all and expect you are pretty busy as the snow starts to fall! Question: Two bed maisonnette on two floors with 9 rads. First floor 4 rads, second floor 4 rads plus one v.small one in ground floor entrance lobby. The second rad in lounge is the end of the line so to speak...

Thanks Leccy - have a part on order now! S

Yes that makes sense. I think it is in the thermostat regulator that thi scan get stuck. I have taken the top off and can see the switches, its a blue box just inside from the on/off knob. Any way to get it unstuck and working again normally or is it a new switch/thermostat job? S