Job done. That valve was closed, in fact the thermostatic valve on the other side leaked.... both ends are now capped, radiator is off and the system re-pressurised and working fine.
Thanks for the advice/suggestions.
Thanks for replies. Using WD40, grips and pliers I've turned it clockwise as far as I can, it's almost flush with the nut:
I can't tell whether it will turn much more or not, but I do have some spare blanking nuts.
Would it be advisable to remove the rad, and put a blanking nut straight over...
Cheers - I thought that might be the answer, but didn't want to risk damaging the valve and causing a leak. Is that how this type of valve is supposed to be opened?
And yes - I'll get a pro in to bleed the system and change the valves etc. once I've finished. Just wanted to save a call-out fee...
Hello, can anyone help me with this radiator valve?
I'm trying to remove a radiator for plastering / decorating. At one end, there is a thermostatic valve which is fine. And at the other end is this, with a smooth round spindle and flat top:
Any ideas on how to turn this off? I've only ever...
You were right - it is the ground floor, I have a cellar below. All wooden wedges/plugs and nails removed (I'm going to plug and screw some new batten in for the skirting).
Sand/lime/cement and SBR purchased this afternoon, so busy day tomorrow...cheers gents.
Hello Vinn - all removed. The skirting was mismatched (obviously been part-replaced at some point), but didn't seem too bad. I guess there has been a problem here before. That dark brick in the middle of photo is made from wood for some reason.
The wall with the plug socket is party wall, the...
I've had a couple round (had to have PCA timber & damp survey for mortgage company). No major concerns, but they both suggested a chemical DPC in a couple of places, with the necessary hack-off & specialist replaster etc. for between £750 and £850 in the room in question.
I'm just loathed to go...
I've also found this stuff from Tarmac called 'Limelite' Renovating (about £25 / 25kg bag in Travis Perkins) which says is designed to have exactly the same properties as the ratios that you mentioned above:
http://www.pozament.co.uk/products/limelite-renovating/
Like I said, I'd really...
Cheers for that Roy. It's basically a Victorian terrace.
I've already knocked-off the boxy/hollow sounding plaster in the above photo, the rest seems sound. It's only in one corner of the room too, the other walls are generally fine, and where the plaster has blown elsewhere - there isn't any of...
Hi
I've just had a re-wire done, and I'm about to fill in the chases / tidy-up before skimming/fitting 7" skirting etc (I'm not going to plaster down to the floor).
I've removed the loose chunks of plaster, but in one corner only there is a soft, chalky layer under the plaster.
Anyone know...
So I went to a timber merchant this morning............and they also convinced into buying 16m of 7" MDF torus, primed. I wanted real wood, but they basically talked me out of it for the same reasons.
£40 and they also cut it down to fit in my car, easy. If it looks good after fitting/painting...
Thanks. I've got a U-shaped kitchen, so will have some units perpendicular and others parallel.
I think this job will involve lots of frustration and swearing.
Hello
I want to replace the laminate in my kitchen (with new laminate of same thickness). Unfortunately the owners before me fitted the laminate before the kitchen, and it goes back to the walls. In my mind I have 3 options:
1. Lay new laminate on top of old laminate, up to the feet of the...
Thanks Gerry - good suggestion with lowering the battens, I hadn't thought of that.
Timberwise, I know very little. I'm aware that MDF would make my life easier, but I'm happy to take my time and fit real wood skirting. I've assumed pine because it seems to be readily-available and not very...