Search results

  1. C

    WMA 37 Fault code

    scrap bin now, !!!!Can you recommend a good replacement machine Bosch ??
  2. C

    WMA 37 Fault code

    Yes Door locks loocks like it working striaght way then Cycle ends after 4 Revolutions
  3. C

    WMA 37 Fault code

    yeah i done that repaired the cables and changed to the new board,but board people mention change the interlock??? Would this be the door interlock? Tried the machine and instead of two revolutions now does 4??? then end light comes on. Fault code A B C D as last post.
  4. C

    WMA 37 Fault code

    Hi I've changed the board on my WMA 37 this afternoon, found the cable s between the motor and the board have worn away against the concrete block. The machine now does 4 spins then it goes straight to End Light comes on. On every program The diagnosis code is A B C D...
  5. C

    WMA 37 Fault code

    Thanks a lot i ve ordered a replacement board, Let you know if it works Cheers again javascript:emoticon(':o')
  6. C

    WMA 37 Fault code

    ive found the problem, the control board with the black relays on where the white motor cables come out,X1 the resistor r35 is has gone to the moon!!!!! :cry: RIP WMA37 2002 - 2009
  7. C

    WMA 37 Fault code

    job for tomorrow i think, will be in touch, many thanks again chris
  8. C

    WMA 37 Fault code

    on a wash cycle The machine begins to fill with water carries out a few revolutions of the drum then stops with lamps lit. on a spin the machine drains then rotates the drum for a couple of revolutions then faults, i have checked the brushes and they are o.k, the motor is only 9 months old!!
  9. C

    WMA 37 Fault code

    The machine is empty now and has been powered off but still it will not run, any ideas on how to resolve it, is it a switch or something??
  10. C

    WMA 37 Fault code

    AH o.k but what does O.O.B mean??javascript:emoticon(':?') No spin due to O.O.B............................on.........off...........off.........off Cheers Chris
  11. C

    WMA 37 Fault code

    My washer has broken down again, the machine starts a cycle then stops almost straight away, it revs the drum, then faults on all cycles, i haved check the fault log and get the following binary fault code a = 0 b = 1 c = 1 d =1 Ive looked at previous old posts but this fault is not...
  12. C

    hotpoint WMA 37 fault lights??

    Thanks Rocks, Got a motor for washer of e bay, the machine is running againjavascript:emoticon(':D') Very Happy thanks again for your great advice its saved me buying anew washer Chris 25
  13. C

    hotpoint WMA 37 fault lights??

    Thanks i checked out the drainage all is clear but this is what have found on the motor. The motor armature moves in the motor maybe 10mm its as if the bearings have moved and allowed lots of end float play too the point where the brushes are almost leaving the armature segments. I am trying...
  14. C

    hotpoint WMA 37 fault lights??

    It s failed again same place in program. I ve the brushes and don't see any arcing from them. they were replaced approximately 1 year ago up till now the machine had functioned correctly What do i need to do to replace the motor triac ?? is it a card or a component change??
  15. C

    hotpoint WMA 37 fault lights??

    emptied sump filter found several plastic toy coins,plastic,and elastic. Now set running again, wait and see time.
  16. C

    hotpoint WMA 37 fault lights??

    Now it's an intermittent fault the machine has just ran through a cycle completely, the only difference than before was that i have set it to time saver mode??javascript:emoticon(':?') Confused
  17. C

    hotpoint WMA 37 fault lights??

    i have put the machine back on wash and i am waiting to repeat binary code procedure !!!
  18. C

    hotpoint WMA 37 fault lights??

    the machine had a 3/4 to full load in nothing heavy. The machine ran for about 30 minutes on wash and then it drained the water as i heard the pump run. It then stopped with the 3 lights on. I then turned the dial to Off and started the rinse and spin program. The machine ran the rinse and spin...
  19. C

    hotpoint WMA 37 fault lights??

    sorry mis read the post with codes i have "motor Triac fault" javascript:emoticon(':cry:') Crying or Very sad
  20. C

    hotpoint WMA 37 fault lights??

    Thanks Very much for your replies i have carried out the procedure and i have the binary code of 1001 however you have 2 errors for this code. Can you explain the two errors "no spin due to O.O.B " and "Motor Triac short circuit"
Back
Top