Search results

I am employed as a electrical service engineer by a company that services Industrial ovens, hot counters and Catering equipment. occasionally I do repair equipment in Petrol station Shops. Last week I was kicked of site by a Station Manager for not having a SPA Card. My...

Fairly new two speed Henry, power accros the on off switch, LED lit up on the two speed switch but it wont run, checked the continuity of the two speed switch and it reads o/c between the brown and white wires and the black, could it be just this or do I need a PCB as well ? Has any one...

A few years ago I purchased a replacement exchange pcb for my balmorel 45 gas boiler, from PCB repair buisness in watford. I have now lost the name and address, and cant find them on the net, does any one know there name, or recomend another supplyer .

A few years ago I purchased a replacement exchange pcb for my balmorel 45 gas boiler, from PCB repair buisness in watford. I have now lost the name and address, and cant find them on the net, does any one know there name, or recomend another supplyer .

I have a dead Technika LCD32 209, when power is applied the blue led comes on, press stanby button goes off then aft a few mins, blue led flashes, any idears.

I have a dead Technika LCD32 209, when power is applied the blue led comes on, press stanby button goes off then aft a few mins, blue led flashes, any idears.

I have a Sony KDL V40A12, its compleatly dead no stand by light, had a quick look with the meter, DC comeing out the bridge rec at the top of the power supply, some one suggested dry joints on the stand by tx, but it all looks ok, any ideas. ( Ex telly man)

Thanks, I can see the point, the inductance would vary depending on the thickness of the wire and its winding method but the DC resistance would obvesualy remain the same.

How can you tell if your house has a soak a way system for surface water drainage ? I was once told that all houses built after the mid 70`s had a soak a way system ? mine was built in 1989/90. and the other evidance of a soak a way system was if the guttering down pipe goes straight in to...

Washes, drains but wont spin fault code E03 or E16 comes up in the display, any help appreciated

Miele or Bosch me thinks, better a nice secondhand Miele than a new B**KO

Hoover washing machine, washes but does not rince, error code E03 comes up, could it be just a blocked drain pump, or do they have a common fault causing this, making it uneconomical to repair. Help appreciated.

I know there different, but I thought if you knew the DC resistance there was then a method to calculate the XL at 50 Hz, and then from that you could calculate the inductance with the formula L = XL / 6.28f. But then I am not a kitchen fitter with part P

Can any one tell me the formula used to calculate the value of a single phase motor start cap, I know this involves the inductance value (L) of the coil, but if this is also not known, is there then a way to calculate the value of its inductance from its measured DC resistance ?

Has any one had experiance of Comets fixed price £99 repairs? I have a 42inch plasma with a Y Sus fault, it needs a replacement PCB, £99 sounds too good to be true to me.

I have a Hotpoint dishwasher approx 5 years old, fills ok but the wash pump is not working, just hums and gets hot, checked impreller, all clear and motor turns freely, it seems to try and work if you keep pressing the on off switch, I am thinking Motor Start cap perhaps ?? I have noticed...

the comments from colin1 should be noted, I belive the HT feed to the Mag is about 4Kv at 500 mA, one wrong move and this would put you on the list for a day out with the undertaker. I was told once that if you measure the volt drop accross the heater and the cathode terminals of the mag, and...

Does any one know how to remove the case on a camercial merry chef 1725 micro wave oven,I cant find any retaining screws just pop rivets ! . the fault is that it wont open one the timer has finnished, any help most appreciated.

My Daughters Hotpoint Aqareous Washer dryer is not drying, the washing it comes out hot and still wet, I know they use water for condensing, is it some thing blocked? all info appreciated.

Many thanks for the advice from all. I am not looking at the job as a long term career, the money`s p*ss poor , I just want to cover my a*se.