Search results

Hi All, Wanted to find out if theres anyone available to finish of an installation (configuration) of the texecom elite alarm. Ive recently had a baby and haven't had a chance to finish off my brothers installation. Ive installed everything (door sensors, room sensors, GSM, Control Panel...

Excellent Secure I AM - Many thanks for that, it was the Elite 48 in the panel section that sorted the connectivity out. Manage to get online now. Thanks

Under Wintex new account panel details, I currently have the premier 48 v2.11 firmware. Im selecting Panel type Premier 48 and software version 2.x (ive tried 10.x as well) Serial number I cannot input anything and password is the default password for the panel. I will try what you have...

Thanks for the quick reply At the moment Im using 192.168.1.150 for the Panel and the router has an IP address of 192.168.1.1. I haven't set port forwarding on the router as of yet as its all internal configuration at the moment and in the past on another install I didnt set any port...

Hi All, Ive recently installed aTexecom Premier 48 unit with 8 PIR detectors, 3 Door impact sensors and one bell. The extra modules are ComIP and the GSM module. Ive configured the IP address via the keypad set the Subnet, Gateway and the default port of 10001. Ive tried everything to try...

Excellent, thanks for the confirmation

Hi All, I would like some advise for a new alarm that im intending on buying. I have listed the items below and wanted to find out if all is compatible with the elite 48 control panel and if 3 keypads can be installed. 1x Texecom Premier elite 48 3x Texecom Premier Elite Diamond Black...

Hi All Was I dreaming yesterdat that a responce was posted here. It suggested in contacting Aico, which I will do this morning to see if I can get the remote and CO2 swapped out after all the tests and money spent on electricians in getting the issue sorted. Its amazing what you can do...

Sorry All, been quite on this thread. Been going through the testing phase. Ok so this is what I've done and so far so good, no damn beeps I went back to the first smoke alarm and disconnected the next in line smoke. The first one was in the loft. I ran this smoke alarm for a few...

Hi All, Everything is hardwired including the remote, nothing is wireless. Is it worth while disabling the remote to see if that makes a difference i.e. disconnect the remote entirely and feed the two cables into a connector block to test. I will also try Workers suggestion to see if...

Hi Yes when you use the remote to test, all the alarms go off. When the button is pressed, alarm goes off and you can then silience all alarms expcept the one which is going off. Green light is always on, on all alarms, however you can faintly see a redish/ amber light flash now and again...

Hi Thanks for getting back to me. The current set up is Smoke, Smoke, Remote, CO2, Smoke, Smoke. All smoke alarms are the Aico EI2110 Multi-Sensors CO2 is Aico EI261EN All alarms have the Hush button The remote is the: Aico EI411H3 Which has the following buttons: TEST - Press to...

Hi All, Once again, Im back with the same problem. For the last two years Ive lived with the Aico beeping smoke alarms but now is enough. The problem I have the first alarm in the chain constantly beeps at random times. Aico support are useless, spoken to them many times but they...

Hi All Ok over the weekend I took everything apart and rechecked everything. Starting from the loft which is the first in line, took everything apart, checked the cabling mains coming in and going out to the next alarm. Refed all the wires back into the alarm Switched on the RCBO then...

HiYa Thanks for getting back to me. Its a dedicated Smoke alarm circuit on its own RCBO 6amp. No lights, just the smoke alarms. I have 3 ei2100 multisensor smoke alarms, Loft, 1st and Ground floor hallway. I have one other in the front porch and I have a CO2 near the boiler...

Hi All Seem to be having a major problem with the Aico ei2100 multi sensor smoke alarms For the past six months, through out the day or night I get a loud beep from the alarm randomly, sometimes every couple of mins, sometimes, every 10 - 20 mins, sometimes a few times in the day. Ive...

Hi All, Having used the texecom system for 3-4 months now, Im now getting a System Alert on the LCD display, message which reads: Low Battery for user X. I thought the battery life on these key fobs were meant to be for about 2-3 years. I probably use the key fob 4 times a day max during a...

Just checked on the o2 website This was the results I got for my area: Sorry a phone mast close to you isn't workingThis means you might experience problems making calls, using the internet, or sending/receiving emails in this area. Updated 11:08 (refreshed hourly). Recent faults might not...

Hi All, Ive got the Texecom Premier 48 system with the GSM dialler. Its been working fine for the last few months since the final installation. This morning I couldnt set the alarm for some strange reason. The errors on the screen im getting is: ATS Path fault Coms 2 error - GSM Module...

Hi Guys Looks like Adrian was right on this one, I opened the mag contact took the pins out from the input section and reinserted them and tightened the screws, closed everything and then launched the monitoring software and everything seems to be fine. I can now set the alarm including...