Search results

My pressure washer has a fault where it won’t start on the trigger reliably. It was repaired under warranty some time ago but I don’t know what was replaced at the time. Can anyone advise what the likely required part is please?

Is there such a thing as a 15 >14mm copper reducer for French plumbing fittings?

Is there a decent sensitive narrow temperature range pipe stat I can use to use as a switched override for a bathroom fan when the shower is turned on? I’ve currently got the flomasta cylinder / pipe stat in place but the water temperature is too low and the measuring type on the stat not...

Having a bit of difficulty in getting this to work! I have a uh4 heatmiser and a vaillant vr71 Currently ls and lr from the heatmiser are wired to s7 on the vr71 as per instruction from vaillant technical and s6 is bridged. Demand from the ufh system does not cause the boiler to fire...

I'm having a bit of trouble with my C300H. The engine to PTO belt keeps slipping off the PTO pulley at the transmission end. It's a right faff getting it back on each time I want to engage the PGC and wondered if there was any adjustment on the belt pulleys (I've had a good look and can't see...

Hi, I have a couple of integrated appliances to fit but am struggling to ensure I buy the correct appliance for my kitchen type. The units are solid wood in frame ( as opposed to over lay ) The instructions for all integrated appliances refer solely to inlay and I’m concerned that there will be...

Does anyone have a tracmaster bcs7** series rotavator / tractor that has suffered hydraulic fluid leak? I’ve been told it’s coming from a failed seal between the engine and transmission body but it looks like it’s recently been pulled apart so wondering if it’s as a result of this or someone...

I've got an issue with the above where by the drive appears to have failed, when I take it apart the end of the armature appears to sit against the inside of the bearing adjoining the gears for the blade assembly but I can't figure out how it transfers the drive, the end of the armature appears...

The handle won’t engage on a new window (initial steps to remove from frame) I applied some pressure to the handle however the clips will not engage to allow the unit to open. Any suggestions?

I have a raised path by the front of my house retained by a dry stone wall about four feet high. I’d like to break the path up and repurpose the space as a flower border however I’m worried that the concrete might form part of the foundations for the house. Is there a way I can check before...

Is it possible to have two bell pushes wired to one doorbell (standard low voltage hard wired style)

I’m getting chattering from non return valves on my heating system when the zone ports or partially open (vaillant weather compensation controlled) Are non return valves essential in this instance or can I remove them? for clarity each zone is piped with flow and return to a bespoke 28mm...

The pressure washer pump does not activate when the trigger is pressed any longer. This was repaired under warranty previously however this has now lapsed. can anyone advise what part is likely to require replacing please? thank you

I’m missing quite a bit of data in my sensoAPP for instance zone 2 flow temperature (zone 1 is present) then nothing at all for zone 3… mom able to control the zones as expected though I’ve tried reinstalling the app to no avail and rebooting the gateway the app is total carp!

Is there a way to wire in a normal style light switch for each zone to manually override the lights controlled by a GJD dygizone? The helpline says yes but having a quick look it wouldn't be possible to install a strapper between the unit and the switch so I'm at a loss how this would work?

Does anyone know how to diagnose a fault on a dream glass dg-12 controller? Seems to be dead. Fast blow fuse had failed replaced and still nothing. No obvious caps failed inside. not sure where a replacement unit can be obtained as the company doesn’t seem to have a presence in the uk

Watching flameports useful videos on pir and override switches I wondered if it’s possible to have multiple pirs and multiple override switches? the scenario is a long house with outdoor lights on the permittee controlled by pirs and the requirement for an override switch at either end of the...

I'm after some help, a roofer has provided me with the batten gauge after I supplied details of my roof. I've managed fine up to the point where there's more than one course and then my brain has given up. Can someone please tell me what measurement from the eaves up to each batten where...

Does anyone know if those old industrial Wandsworth switches came with two way modules?

I’d like to be able to take two 230v feeds to one output, do I need a contractor for this? One input is from a vaillant vr71 to control a secondary pump and the other from an occupancy sensor. I would like both to be able to control a single pump. I was thinking a contractor but they all seem...