Search results

http://www.machinemart.co.uk/shop/product/details/clarke-cew1000-electric-impact-wrench?da=1&TC=SRC-impact%20wrench Am thinking of buying one of these for occasional use on the car.Has anyone bought/currently using one of these.Not as powerful as the air wrenches maybe but to be used now and...

Notifying the BCO to install your own system;is this absolutely necessary?

hi, have been browsing and saw this particular package on ebay. http://www.ebay.co.uk/itm/4-Security-Sony-CCD-Waterproof-Cameras-H-264-Network-1TB-DVR-Surveillance-System-/170723021283?pt=LH_DefaultDomain_0&hash=item27bfe291e3. It looks ok on the face of it.anyone got opinions? thanks.

eyup, They all look like pieces of qualit kit but which one gets the money.I currently own a bosch SDS DRILL which i,m happy with so maybe go for bosch again but the makita or dewalt......??

Hi, Which type of screw and size should i go for to join the joists?-i don't want to nail .after doing some relentless searching i found one or two use the above screw but can't find a stockist.i'm wondering which type you guys use and where to buy in bulk? many thanks.

hi, we're currently in the process of removing an old drive that has been layed in the past. i am thinking of adding some of the old ballast/hardcore and compacting then adding some postcrete to the post holes that i've dug out ready to start a decking project. is this ok-i'm thinking it...

gonna have a go at making some decking. i'm wondering how many supports and how deep i go? i've been told: set them at 600mm centers and a foot deep(raising it 6" from the ground )using 4"x4" posts or maybe using 3 at 800mm centers.(18" each post) has anybody got some advice please...

are a right bugger to get back on :oops:

bon soir, just bought one of these from cromwell to nudge the beading back into place.whats th knack with this beading,im lil curious??

hi, in relation to a similar post the other day,i just wanted to know how you get the external beads back on without breaking them,ive useda rubbermallett but tends to bounce.ive heard that the thor hammers are quite useful,im being cautious here but maybe a sharp tap with plastic faced...

hi all, ive took the unit out today by removing the rubber seals on the inside and then removed the beadingwith(after a lot of searching in the kitchen cupboards) a PIZZA CUTTER.the measurements were 872x365 but the thickness was only 19mm.the question is would i be able to get a...

hi all, i was wondering if i could change these without removing the whole handbrake assembly and complete the job by just removing the heat shields and unhooking both cables from the equalizer bar???? many thanks.

ive come across this today and im not sure wether it totally breaks the regs??? whoever fitted the bath has capped the original waste off because there is no proper run off to drain the bath quick enough and so run a length of pipe to the toilet waste and connected there??? oohh err :roll:

hi ,ive been getting a rattle for a month or 2 now and its getting worse.its seems to be coming from the inlet.just to add the oil level is ok and the belt tensioner is about 3 months old.i know this has been a problem on the early mk 3(mines 02 plate ) with the shafts breaking and the little...

hi here goes with another question on my bloody brakes. after having new calipers,discs and pads on the rear,the travel on the handbrake is fairly excessive and only just got through the test. ive had the center cosole off today and noticed that there is slight travel,maybe an inch before it...

after changing the calipers a few months ago ibled the brakes following the "book" .after doing it and driving it i wasnt 100% happy cos the pedal was a bit spongy.anyway last weekend i had another go and im still not 100%.there must still be some air somewhere..little buggers!!. the calipers...

hi to all, quite recently the car is making a rattle near the timing chain end.it is quite evident at idle and seems like the problem is worsening.ive checked all bolts near the vicinity..alternator and drivebelt etc and its definitely coming from camshaft orcylinderhead.i know that without...

hi,its one thing after another with cars innit!!first the rear calipers went,got an irrepairable puncture on a nearly new tyre now this.after sourcing the leak ive discovered that there is a crack right underneath the tank afetr removing the 3 10mm bolts and having a look yesterday.when the car...

hi.is this ready for a clean up around the burners?? my instinct says it is or is it ready to be replaced?? im on a budget ..any suggestions if it does?? thankyou

hi the above has just started doing this.its noisy( metal tick tick tick on idle and at low speed..you can hear it plain as day as you move on up from 1 to 2.as the vehicle speeed increases the noise dies down.could it be that the valve clearances need looking at or summat else.the oil has just...