|
Trend CRAFTPRO Keyhole Router Cutter 9.5mm 4.5mm 1/4"
For picture hanging flush to the wall. Plunge cutter & move forward, then retract out from entry hole. A template is recommended. For No8 & No10 screw heads. Not suitable for grooving applications. Specifications: • Sha... |
£25.95 More Information |
|
Trend Two Flute Long Reach Hinge and Lock Jig Router Cutter 12mm 19mm 1/4"
Two flute TC cutter giving good chip clearance. Ideal for shallow lateral routing cuts such as recessing hinges. Corners will require final trimming square with a hand chisel or a corner chisel. Suitable for Trend Hinge & Lock Jigs. ... |
£36.95 More Information |
|
Trend HSS Single Flute Straight Cut Router Cutter 4.8mm 19mm 1/4"
These are made from a single piece of High Speed Steel, ground with a very fine edge. They are only suitable for non abrasive materials, but will give a superior finish in soft timbers. Generally HSS cutters are slightly less expensive than t... |
£13.95 More Information |
|
Trend Professional Two Flute Straight Router Cutter 18.2mm 21mm 1/4"
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Diameter: 1/4 • Dia Metric: 18.2 ... |
£39.95 More Information |
|
Trend Intumescent Strip Recesser Bearing Guided Router Cutter 27.05mm 10mm 1/2"
Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door. Two sizes available to suit 4mm thick strip of 10mm or 15mm width. Intumescent strip is used to create an effective barrier to both fire an... |
£59.95 More Information |
|
Trend Down Cut Shear Two Flute Router Cutter 12.7mm 50mm 1/2"
Tungsten Carbide Tipped. Two flute cutter with a positive shear angle (down-cut) for fast cutting and fine finish. Ideal for grooving & trimming veneer finishes & laminated boards. Down cut feature stops break out on top edge. Has a 3 de... |
£51.95 More Information |
|
Trend Professional Two Flute Straight Router Cutter 21mm 19mm 1/2"
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Diameter: 1/2 • Dia Metric: 21 &... |
£56.95 More Information |
|
Trend Replacement Cutter Bearings Metric OD 35mm
Bearing for slotting systems. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. Specifications: • Cut Length Metric: 8 • Bearing Dia Metric: 35 • Sawbor... |
£15.95 More Information |
|
Trend Imperial Replacement Cutter Bearing 3/8"
Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Alw... |
£9.95 More Information |
|
Trend Professional Two Flute Straight Router Cutter 30mm 25mm 1/2"
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Diameter: 1/2 • Dia Metric: 30 &... |
£80.95 More Information |