|
Trend Chamfer V Groove Router Cutter 51mm 25mm 1/2"
Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Specifications: • Shank Diameter: 1/2 • Dia Metric: 52 • Cut Length Metric: 25 • Overall Length ... |
£114.95 More Information |
|
Trend Rota-Tip Bearing Guided Round Over Router Cutter 26mm 15.7mm 1/4"
Two blades. Replaceable tips increase productivity. Low profile bearing fixing screw. Specifications: • Shank Diameter: 1/4 • Dia Metric: 26 • Cut Length Metric: 15.7 • Overall Length Metric: 52.5... |
£63.95 More Information |
|
Trend Bearing Guided Template Profiler Router Cutter 25.4mm 45mm 1/2"
Profiler with shank mounted bearing guides. For use with router mounted above or below a table when following a template. For profiling and rebating applications only. Not for plunge cutting/grooving. A 3mm maximum overlap should be le... |
£82.95 More Information |
|
Trend Professional Two Flute Straight Router Cutter 12.7mm 32mm 1/2"
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. TC tips are ground with greater clearance for routing of resinous material. ... |
£33.95 More Information |
|
Trend CRAFTPRO Weatherseal Groover Router Cutter 34mm 2mm 1/4"
Two fluted tungsten carbide weatherseal groover for use on natural timbers and manmade boards. The cutter is non stick coated to reduce resin build up. For use with smaller routers where application allows. Neatly cuts grooves on doors or frame... |
£51.95 More Information |
|
Trend Replacement Cutter Bearings Metric OD 19mm
Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Alw... |
£15.95 More Information |
|
Trend CRAFTPRO Small Ovolo Router Cutter 9.5mm 7.9mm 1/4"
A small beading cutter for fine decorative panelling, veining or rounding over. Specifications: • Shank Diameter: 1/4 • Dia Metric: 9.5 • Dia Imperial: 3/8 • Cut Length Metric: 7.9 • Cut Length Imperial: 5/16 ... |
£24.95 More Information |
|
Trend Two Flute PTFE Coated Non Stick Router Cutter 4mm 11mm 1/4"
Gives a clean finish to abrasive materials such as chipboard, MDF, plywood and certain hardwoods. For housing, grooving and mortising. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long lif... |
£24.95 More Information |
|
Trend CRAFTPRO Large Dovetail Router Cutter 12.7mm 20mm 8mm
These cutters are for Trend Craft Dovetail Jigs. Specifications: • Shank Diameter: 8 mm • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric: 20 • Overall Length Metric: 60 • Angle: 98... |
£23.95 More Information |
|
Trend CRAFTPRO Two Flute Straight Router Cutter 6.3mm 25.4mm 8mm
Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. Specifications: • Shank Diameter:... |
£16.95 More Information |