Search results

Hi I have a bar in my garden that has 3 beer pumps, these all have LEDs that light up the beer signage on the pumps, these 3 are all wired separately. I also have 7 x 2w LED bulbs that are wired in series. These pumps and bulbs are all 24v but was wondering that although the 24v transformers...

Hi Not too sure if I’m posting this in correct forum. I’ve got wood panelling on my walls in my Dining room. My previous house had wood panelling too and it was a lovely dark colour. Well this house the panelling is not so nice looking. When it was bare wood it was originally stained using...

Hi Hope I’ve put this in the correct forum. I’ve a 4m x 4m Internal concrete floor, its years old but in good condition. I’m going to be laying a laminate floor over it. I’m going to be putting down a dpm with 75mm of ecotherm for insulation. My question is should I lay a second dpm on top...

Hi. @secureiam previous questions: Have swapped black and blue from zone 6 to a known working zone black and blue and redone the walk test. No difference. Which sound bomb are you using? Kinetic Sound Bomb KSB1. I have checked that the zones are set as used/unused as required. door is set as...

I’ll have a look at the sound bomb in the morning and get back to you.

A strobe

A strobe

I have only got 1 pir. Zone 6 is programmed as used yes

Sound bomb is working in speaker output. Not using the zones consecutively as the screws Heads on the unused zones are stripped so can’t undo/do up screw. the unused zones have been programmed as unused. Should I still link them out?

Not using a bell box, have a sound bomb on the speaker. White & green go to 13v & 0v in panel. No joins

pir is using zone 6. It’s not a faulty pir as I swapped a known working one in. It’s wired the same as the main house Accenta that works!!

Hi That what my pirs are: power pair alarm pair tamper pair although I have no tamper wired. All tamps looped out. The terminal labels were like that when I opened the box, I’ve also got an Accenta G4 with these pirs in the main house, have checked and although the wires are indeed different...

Maybe wrong colours yes

Does this help?

Ok. I think I did what you’ve asked. In walk test the pir picks me up but does not activate i.e: stays at 0 If I take a blue zone wire out of pir end on walk test the zone is set at 1. The pir picks me up. If I rewire pir end and take a Blue zone wire out of panel on walk test the zone...

I’ve just installed an Accenta G4 consisting of 3 x contacts and a PIR. When I go through the Walk Test the contacts all work but the PIR does not change from zero to 1. The PIR does flash but not activating when alarm set. The PIR is wired as follows: Pir + to panel 13v+ Pir - to panel 0v...

I have looped out the sab and the tamper faults gone now. My next problem is getting the pir to trigger. It flashes but doesn’t trigger??

Hi No bell, just an external speaker. Have checked the keypad and panel and both ok. Have stretched the springs a little to be sure. No tamp wired for pir. I’ve looped the PA, Tamp and the panel ramp but still getting fault. What now do you think? cheers

Hi Second Accenta G4 I’ve installed. This one is in my man cave (don’t judge me) Anyway it consists of 3 contacts, a PIR, a strobe and a external speaker. I have not bothered with tampers. Inside the unit both PA and TAMP are looped out. When I power up the unit I get a Tamper Fault...

Quick question. I’ve a consumer unit with a built in RCD so was wondering if I have an outside plug in the garage I’d need to use either a plug in RCD or have a socket with RCD built in. Thanks for your help