Search results

Spot on...centre it is! Was debating front or centre but cant go wrong with it in the middle Thanks

Hi guys just a quick one. I've had a small outbuilding built in my back yard. Using as a sorta workshop. I need to fit a pvc door and window and need some help. The building is only single block and i just wanted to know where abouts do people recommend to fit the window and door. Towards the...

Just noticed the title should be fitting not forting.....

I'm thinking of capping over the timber fascia on my garage to make it look a bit neater but have a few questions... The felt roof over hangs onto the fascia and looks pretty tight to the timber. Is their a way of fitting the fascia up and under the felt or is their another way of doing it...

Be rude not too in this weather

Switched fuse spur

If need be i can take the cable its an ip rated box and use this as a juncuon box for the 2 lights. Just wondered if the sfs could take 2 light?

Currenlty have a half lantern outside the back of my house controled by a sfs fed from a double socket inside the house. Will i be able to run some cable from this light into a a small bulkhead around the corner? Need a little extra light and thought this would be the easiest way?

Pic of what? The master door locks against the slave but the slave wont lock even if the door is open? Faulty barrel? Does it need some adjustment before it can lock? When i lift the handle it doesnt seem to go as high as the master handle

Had a stroke of luck when i went into a local store as they had a miss-measure door which was only 30mm to short but packed it out with an add-on. Only problem now is that the barrel on the slave side wont lock?? Any suggestions??

So basically i cover the cavity with a length of plastic?

No problem. Its a pretty old house and i think their is 2 course's of red brick. If i fit on the outer brick wont that expose the cavity? What happens then?

So it is as simple as that? Lol Just looking for tips on the installation of the actual door. Where abouts do i fit the door? on the outer or inner course of brick? Back to the current plaster line? I understand it has to be plumb and square ect...just looking for tips on the not so...

Thanks foe your reply... The current window is roughly 1750w and 2050h. I dont think i need to cut anywhere as the bottom half of the window is roughly 1000 high with a flat panel and the window is ontop of this is fixed togehter by a coupler. I was thinking of just ripping this out and...

Hi guys, Moved into a house which has a full length window in the lounge to the floor with a flat panel accross the bottom half and the window ontop.Thinking of taking this out and replacing with pvc french doors. Any tips or pointers on how to install the french doors?? Thanks for your comments

The house is rcd protected but i need a light too. thats why i was thinking garage unit. No pipes in their yet, thats the next step....

Morning guys. Just bought a new house and need to get power to an outhouse literally 1m away from the house. All it needs is a double socket (to run a washing machine and tumble dryer) and striplight. Their is a double socket in the house on the outside wall which i wont be using. So i was...

Its a honeywell 2 channel programmer, not sure what model!? Its controling hot water and heating. I also noticed that theirs 2 x 0.75 (I think) flex coming from the controller into a JB then 2 x 2.5 flex running to the actual boiler! Is this ok? Or should it all be ran in the same size flex??

I'm not installing the caravan point now All I'm doing is extending the ring for each room and the extra sockets and the feed into the garage

Thanx for the advice guys, think ill take a feed from the house like I intended. When u say take a FCU for the light do you mean off the 2.5 and run 1.5 to the light? Or should I try extend from the lighting circuit in the house? I suppose either would work? Can you have 2way switching off a FCU...