Search results

Hi I would be greatful of our some help my mira advance 9.8kw shower has operated faultless for a number of years - it has now developed a number of intermitent faults It flashes up a red light - service required - then runs cold - some times if it is switched off it will restart other...

Thanks Gas Guru and Holty it appears to be fixed..... will see in the morning Thanks Haven

I have bleed all the pipes upstairs and it appears to have fixed the fault, will give it 15 minutes of rest to re-test the cold water tap Thanks and fingers crossed - will post a reply Haven

Thanks holty, I will go and bleed the 1st fix, but one problem, i have put a hot water feed in for a mixer shower (for the future) and placed the plaster boarding over this! i have planned for a electric cold water feed shower.... thus i have the cold water feed protruding from the wall and...

Hi again, Just been and purged the hot water and cold taps in the garage and utility. Whilst in the garage (Boiler installed here) when i turned on the cold supply, the boiler only switches on when the tap is switched off. I could hear a click (twice) of a switch/valve? I have re-tried the...

I have not bleed the new upstairs bathroom cold and hot water circuits due to the fact that i am at the first fix stage i will go and try all the other taps round the house that have not been used (utility and garage) Thanks

Hi, My boiler is firing up to run when we run the cold water tap. The hot water system is fine, with the hot tap running and the water is hot. I recently plumbed in a upstairs bathroom and was wondering if a small amount of water hawk compound has found it way into the system and partially...

Thanks for the help and advice, it looks like either a second hand waher (local charity re-cycling and repairing white and grey goods etc) or repair (Wife and 2 young children will not wait!!) Thanks once again Haven

Thanks for the help and advice, it looks like either a second hand waher (local charity re-cycling and repairing white and grey goods etc) or repair (Wife and 2 young children will not wait!!) Thanks once again Haven

Thanks for the reply, is the bearing fix a diy task or a tradesperson? If not a diy task - what woul be a typical cost for the part and labour Thanks

Hi, I have a Hotpoint aquarius 1300 spin washer, about 1 week ago we had a load of whites come out of the washer a slight off grey/white colour and some grease marks on the clothing. I have loaded the machine tonight and spun the drum both loaded and empty, it runs free but is noisy(grating...

have tried the reset, with no sucess. I have also switched the mains feed off and back on several times, this clears the fault. Then when i turn on a hot tap, the fault reoccurs. BG want 144 puonds to fix. Is this resonable? Thanks in advance

Hello, I have had the electric board re-routing my mains supply today and i have had no power to our house. Once re-connected, my boiler is fault coding C1 - Fan speed too low? I do not know if the electricity is a red herring or just that the fan is U/S. Is it a easy fix? what cost can i...

I have had the motor bench tested by a electrician at work and local repair man, no faults were found on the brushes, no earth leakage (grounding) reported on the motor and both windings appear to be intack, tacho on the rear of motor seems to be intact and pulsing?!?!?!?! but my electrician did...

i have tried to spin the washer with a wet load and without a load. No luck! The non-loaded drum did eventually spin with some help from me, spinning the drum from the rear inspection cover, but the speed control was unusal. I will take the motor (and i think integeral speed control unit)...

Hi, Thanks for the quick reply. Just been to the machine (garage loaction), tried to spin the wet load in the machine. No luck. I have checked the filter and found a couple of coins!!! i removed these and then set the machine to drain....then i removed the filter again to find it full of...

The machine starts its cycle (Fill) then once the wash cycle starts, the drum will not turn a full revolution, as if the motor does not have enough power? or the belt is slipping? Do belts slip?

Hi, i hope some one may be able to help? I have a tricity bendix 851 washining machine that wont agitate once i have loaded it. I have checked out the brushes and they are ok. The machine spins under no load conditions. Any ideas??? Thanks in advance