Search results

Cheers rocks just checked the heater and there is continuity, to clarify the wires i checked were the brown (left) and blue (right). Does this mean it looks like the heater relay and therefore a new board ? I have used your past posts and found the supplier you recommended has one for about 60...

Where is it located please mt

Hi I have searched the forum and seemingly found what is wrong with my washing machine. Firstly the error codes pointed to a blocked filter so I removed that and with it a few quid in change, this rectified my problem for a few days then another error code pointing to the pressure sw stuck on...

Not sure i understand correctly but a low level pan and cistern with a flush pipe allows you to fit the pan further away from the wall. The vertical waste can then have a 90 bent pan connector in to attach to the wc...

But it's just soooo sooooo tempting lol .... Lesson learned on that score since being out of pocket for one new prv an hour fitting it and an half hour in the merchants. :cry: Attach a hose to a drain off on one the rads (that boiler should have at least one fitted somewhere) and let the...

How do you mean one job short ..?? I had to get 80 hours filled into a gas diary but my assessors only sent off my ACS assessments to BPEC ie. CCN1 - Core, CEN1 - Boilers upto 70kw, CKR1 Cookers, CPA1 - Flue gas analysis, HTR1 - Gas fires,Space heaters and finally WAT1 - Water heaters. I then...

Box it in ....Use conduit ... Bury it in the wall....Either way your going to get a run of pipe off to the radiator anyway.. Use plastic you get the privilege of using a gigantic fitting. Worked in a house the other week and they had OCD about copper pipes too and they had them perfectly...

That is indeed your bleed screw/nut mate loosen it let the air out and your heating coil should fill and give you HW back. Id leave the pump off while you do it mate. Long as you get that coil filled and circulating again any traces of air should find there way to radiators. Just re-bleed...

Lol I can see he makes loads of friends Fired on any test mate but all sorted now 3-4 bridge had indeed been removed to make way for a room stat but sparks removed that too as they had a faulty unit. Explains them chuckling away when i tried to fire it. :roll: Gits ive to go back now...

Nor could you O wise one Joe sussed it in an instant now that's experience perhaps you should have spent less time antagonizing people on forums and got some work in :wink:

Point me to when you helped please .. As for argumentative yea i am it helps antagonistic people get there kicks. As for your comment about social housing that just allays what sort of individual you are. Tony I will argue with you until doomsday

Yes it's more than occured they may have stitched me .. lol Yes ive been fitting gas unregistered for the last 3 years it's a requirement in the modern day that a gas installer gains a minimum of 80 hours on-site with a registered installer (ive got 3 years worth plus many more with my...

lol it isnt a fault as stated the boilers working fine in diagnostics just not getting any demand for heat. Agile you didn't even reply to ME in your post so why even bother replying, your reply was not an attempt at help in any shape or form, just a mere excuse to climb on the soapbox (See...

Did read this in in the installation instructions and is the reason i mentioned the clock.. Yes its the standard analogue clock and no room stat. Boiler looks to be working just fine but there just seems no demand for heat on CH side ill give this a look tomorrow. Im pretty certain this is the...

Tried removing time clock mate but to no avail boiler fires on central heating demand then off it pops again with no fault code. HW works fine as does the CH in test mode as i went throught the tests whilst commissioning. Ill re-check sparkies work in the morning but im not allowed touch it...

In other words you havent got a clue :lol: Experience there !!!

Just installed my first one of these and it dosent seem to want to go into heating mode. Sparkies came in and sorted the wiring out but there has since been a vailant time clock added.... Now when the boiler is switched on and there is demand for heat at the central heating it does nothing..No...

Id inform your neighbor out of simple courtesy and he/she may well be up for getting theirs done and willing to share the cost. You may well get it cheaper !

Hi all Firstly I have removed a back boiler and fire and intend to fit a new gas fire, the builders opening is 100mm to large to accommodate the closure plate. I intend to render the insides of the opening but fear that 50mm of render on each wall is to thick. I have thought of dot n dabbing...

As a great Welsh singer once said "it's not unusual". As he states in the post he wants pumped hot water, maybe the guy just can't live without his power shower. Ok so it's not energy efficiency as we'd like and I would advise against it but if your running your heating and have the option to...