Search results

Nothing in the instructions fault finding, just an explanation of an error code if there is no water flowing to the unit, nothing about too much! I did try turning the unit on and switiching the steam function on but it kept flowing so turned it off smartish. I assumed there is a solenoid...

They say it is not supported anymore as the original suppliers of the steam unit went bust!

Not sure whats going on but I connected up a steam shower yesterday (Villeroy & Boch) and when opening the water valve (cold side) I heard the steam generator filling and then water just poured from the steam outlet......no steam of course as I had not even activated the steam function, but its...

Last winter, by my local Gas Safe central heating expert...... :roll:

Mysteryman, yes indeed I mean the ignition lockout, my mistake sorry. I have a qualified gassafe chap in maintanence at work who is willing to look at it but he knows absolutely nothing about domestic boilers, the boilers he works on supply hot water for a 40 acre industrial site, maybe...

No, its been working fine all summer heating the hot water, last week I turned the central heating on as well and now the ignition cutout keeps activating again. Best regards David

Our boiler played up last winter and it was repaired (term loosely used) by a local tradesperson (term very loosely used) , the original problem was the ignition cutout coming on regulary, he replaced virtually every board and control box in the boiler and cleaned the burner. It cost me about...

There must be loads of these shower doors with the same problem now, nobody heard of a solution?

I have a problem with the small plastic roller bearings top and bottom of the shower door they gradually wear and fall apart, I have replaced them twice before by just ringing Aquadart and they sent replacements out FOC. Unfortuantely now the company that took over the name refuses to honour...

I actually found the small ball from the valve in the trap, took the PRD pipe assembly off and popped it back in......all working fine again now. And before anyone says it'll blow up now I tested PRD assembly on my compressor air tank and it blows at about 20psi, not much at all and as a...

Great news, thanks a lot for the info. David

Thanks for the reply, it looks to me that the PRD valve is within the heater element unit, the "overflow" pipe comes out of the heater uniter just behind the main shower head outlet, not a seperate valve it seems! Although looking on the Triton website the later showers have the PRD valve...

Hi, we have a Trtion electric shower, this morning it started leaking from behind the water outlet, upon investigation it appears there is a PRD safety valve which opens in event of a blockage in the shower hose or head (both of which have been removed for the investigation, there is just the...

Had a look under the cover on the CH motorised valve and although using the manual lever does not travel far enough to activate the microswitch, with the cover off I can see that when the valve is eletronically motorised the vlavle inside travels enough to activate the microswitch, so I am...

OK so the rads start going cold after about an hour or so with just the HW turned on, if I then switch the CH on there is a motorised noise from the CH valve and the rads get hot. This early morning thing is my puzzler, if there is a microswitch in the CH valve is it possible this is not...

Hi thanks for the reply, strange thing is the system doesn't seem to want to turn on in the morning although I have the CH switched to 24hrs. I will try the HW only this afternoon after giving the rads time to cool down, I am not sure that is the total problem because although the rads heat...

Well we thought we had it sussed....but now the CH will not seem to work if left to the programmer to turn on, if I turn on the HW on the programmer or leave the programmer to auto turn on the HW we get the heating working as well........but nothing I do on the programmer CH controls will start...

Well its easy for you or I to say "of course they do" but there are plenty of people who are taken in by all the high tech hype thats put into advertising these cables......spread the word, get rid of the snake oil manufacturers! :)

I have had a Samsung 50" Plasma for about three years now, its been perfect.....no issues with buzzing or screen burn despite my son leaving the set tuned to BBC News with the banner footer across the screen for hours......the latent image soon burns away once normal TV viewing is resumed...

Cheap HDMI leads are fine, I buy mine from the dreaded bay at whatever price is best, I have two 15 metre cables for my projectors which perform faultlessely, I think they cost about £10 each, the cables not the projectors :D There was a tes recently, I think by Which, and the cheap cables...