Hello all,
I have installed that panel 2 years ago and i have the following issues.
Panel allerts:
MAINS POWER OFF
PS FAILURE
POWER O/P FAULT system 12v
Going through the log in wintex i have hundreds of logs for the last 3-4 days:
MAINS AC ALARM
Panel and version number is:
ELITE 48 ENG
SW V2.02 LS1
For sure i have power to the panel and the PS working because:
1. System voltage in wintex is 13.82V
2. Manualy switching off power keypads dim and system voltage in wintex drops.
Reading various posts i thought that maybe the battery was dead (even if its only 2 yrs old) but that doesn't seem to be the case as switching off power the system works for hours with the battery. (it is a 12V 7.2Ah battery).
Last night after having the power off for hours i switched power on reset the faults and armed the system. Everything was ok fualts cleared system armed. This morning i had again the same faults since 4:30 am (according to wintex log)
Any ideas please???
Second issue going through the manual after that problem i've read that GSM module should report status as the following.
Sending sms to panel ???? status the reply should be :
“5678 status” =
Armed: (1 - 8 or A - P)
Alarm: (1 - 8 or A - P)
Output: (1 - 8 )
Mains: (OK or Fault)
Battery: (OK or Fault)
Phone Line: (OK or Fault)
If i text the panel (even if its armed or not) i always get the same reply back:
Output: (1 - 8 )
Mains: (OK or Fault)
Battery: (OK or Fault)
Phone Line: (OK or Fault)
I dont get the area that is armed! Any ideas on this???
Sorry if its too long but i wanted to be clear with what i have done so far.
Thank you.
I have installed that panel 2 years ago and i have the following issues.
Panel allerts:
MAINS POWER OFF
PS FAILURE
POWER O/P FAULT system 12v
Going through the log in wintex i have hundreds of logs for the last 3-4 days:
MAINS AC ALARM
Panel and version number is:
ELITE 48 ENG
SW V2.02 LS1
For sure i have power to the panel and the PS working because:
1. System voltage in wintex is 13.82V
2. Manualy switching off power keypads dim and system voltage in wintex drops.
Reading various posts i thought that maybe the battery was dead (even if its only 2 yrs old) but that doesn't seem to be the case as switching off power the system works for hours with the battery. (it is a 12V 7.2Ah battery).
Last night after having the power off for hours i switched power on reset the faults and armed the system. Everything was ok fualts cleared system armed. This morning i had again the same faults since 4:30 am (according to wintex log)
Any ideas please???
Second issue going through the manual after that problem i've read that GSM module should report status as the following.
Sending sms to panel ???? status the reply should be :
“5678 status” =
Armed: (1 - 8 or A - P)
Alarm: (1 - 8 or A - P)
Output: (1 - 8 )
Mains: (OK or Fault)
Battery: (OK or Fault)
Phone Line: (OK or Fault)
If i text the panel (even if its armed or not) i always get the same reply back:
Output: (1 - 8 )
Mains: (OK or Fault)
Battery: (OK or Fault)
Phone Line: (OK or Fault)
I dont get the area that is armed! Any ideas on this???
Sorry if its too long but i wanted to be clear with what i have done so far.
Thank you.