Sorry, sorry, sorry
it is an elite 24
firmware 2.11 I think (I've just been back into wintex but couldn't find where the firmware version is, I can't remember where I saw 2.11)
I have tried
secureiam
on the keypad, enter engineers code.
7 yes, 8 yes (should now be saying on...
Hi sparkymarka
Check via keypad not wintex go to comm port set up , if you go to comm 1 and it says nothing fitted press reset that will clear the comm port of any errors ,
I did what you suggested it said nothing fitted , I pressed reset then came out of the menu's but it still says com...
Hi secureiam,
my alarm is the premier 24 not the elite.
I have a com port 1 fault at the moment
and In wintex
In the radio pad com port options
I have onboard digi com as com2400 module
com port 1 and 2 as nothing fitted
com baud rate 2400
expansion port nothing fitted...
I have managed to get the alarm to text me but it still has com port 1 fault displayed? If I try to arm it says do I want to arm with faults.
In wintex
In the radio pad com port options
I have onboard digi com as com2400 module
com port 1 and 2 as nothing fitted
com baud rate 2400...
My latest update
I HAVE A WORKING ALARM IN THE HOUSE AND SHED :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P :P
I decided I wanted each keypad to local arm disarm via user options.
I also switched zones 9 and 10 (mapped...
Hi just thought,
maybe when I said
"I just tried to arm the shed(area B) and nothing happened so I decided to check the detectors out. I went to eng and walk test. I chose area B but it showed *none*. Does this mean it can't see my 2 zone inputs into rkp 2 (area B)?"
What I should have...
Again it's only me sorry :?
Hi secureiam
"Zones 9 and 10 have 2 wires in alarm and two wires tamper.
zones will be guard area B and wiring type double pole/eol. "
Previously on this post I have been advised to select normally closed . I actually don't have zones 9 + 10, I don't have...
Only me again
In wintex if I have selected A for rkp 1 and B for rkp 2. So does that mean rkp1 will only arm area A and negate the need to press area when trying to arm ? Or do I have to select local arm disarm from user 1 options? again to negate the need for pressing area when arming...
Hello again,
I enabled quick set on both keypads.
I just tried to arm the shed(area B) and nothing happened so I decided to check the detectors out. I went to eng and walk test. I chose area B but it showed *none*. Does this mean it can't see my 2 zone inputs into rkp 2 (area B)?
In...
Thanks again for your replies, I really appreciate it.
I would basically like the shed (area B) to be totally separate from the house (area A) apart from if it goes into alarm I would like the digi modem to tell me, if thats possible?
I would like to arm area B from either the house or the...
Sorry another question,
do I have to tick system configuration option 33 - enable text to get the text I have assigned to each zone to show up?
Thanks, Si
Went back in the loft and found 2 things.
When I tried before with the link i'm guessing I didn't have it in tight enough because the fault cleared this time.
Then I found a suspect broken wire in my tamper circuit, well suspect enough that as I tried to reinsert it broke off.
All...
Cool, progress.
It let me in. I went to the confirm devices menu and it shows rkp 1+2 or something like that and asked me if I wanted to confirm, I said yes. Then I had tamper faults but realized the panel was still open and my computer plugged in. I unplugged computer and closed panel and...
Hi thanks ,
I will untick eng + user in global, select normally closed very shortly and get back with my progress.
No I haven't set up the 2400 yet I was going to ask that question later ;-)
I have set keypad 2 and it's 2 detectors to area B and would like to be able to arm (area B the...