Recent content by jpowell79

  1. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    wired everything up over the weekend, but am getting some errors: System Alerts: Panel Lid Tamper (yep, the lid is off the 64-w :) ) Confirm Devices (possibly the Texecom Connect SmartCom?) EXP 1,1 Tamper (I'm guessing because the 64-w jumper on the right between the two aerials is in...
  2. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    Got ya! thanks again, think I'm ready to give this a go!
  3. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    Also, just been looking through the manual, from what I can understand, in my particular setup, I'd set the zones as follows: z1 (Fault Relay - Front of House Sounder) Zone Type = 12 Auxiliary Wiring Type 8 - WD Monitor z2 (Tamper Relay - Front of House Sounder) Zone Type = 13 Tamper z3...
  4. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    Thanks, genuinely really appreciate it! Ok I think I'm good to go then I'll swap out the 8-core with 12 core and set it up as follows: Do I need to join Aux connector to Fault connector on the 64-w control panel if it's not being used? Same question for Tamper (C) on both the bell...
  5. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    Still a bit confused about the MSW thing on the sounders though.... so I don't need to wire MSW2 on the front sounder to MSW1 on the rear sounder at all?
  6. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    thanks for all your help! So based on the 8 cores I do have wired to each bell currently, I could do this? I guess that really only leaves the "Test T" connection on each sounder (assuming I don't need to do anything with the "MSW" wires now?) In all honestly, its probably easier for me to...
  7. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    Ok so: A = 12v = Red B = Bell = Blue D = 0V = Black S = Strobe = Green Brown, White Orange, Yellow Nope nothing else planned for this setup, so basically use all four zones then to be able to determine either a fault or a tamper on each sounder? So basically, if I wired it like this, I'd...
  8. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    Thanks, so I should wire the fault relay to two zones on the control panel (even though I only have a single physical zone), and this will allow me to tell which is which from the button panel? Do I program both Z1 and Z2 as "auxiliary"? Which color core (on my diagram) should be the spare...
  9. J

    Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders

    Hi all, would really appreciate if someone could help with some confusion I'm having with the wiring of a Texecom Premier Elite 64-W with dual Elite Odyssey 1 external sounders. Just to note, this is what I have: Texecom Ricochet Premier Elite 64-W Control Panel 2x Texecom Premier Elite...
  10. J

    No sound from Texecom Premier Elite

    Did them both like this…
  11. J

    No sound from Texecom Premier Elite

    haha now you’ve said it, makes sense! :-) will double check how I’ve wired the sounders. Cheers
  12. J

    No sound from Texecom Premier Elite

    Finally got round to trying to wire up a new Texecom Premier Elite 64-W with dual elite sounders for the front and back of the house. wired it all up, switched it on and only got the alarm out of one of the two alarms. I’d wired up everything into the same ports with the same colours, with the...
  13. J

    damaged the screw in a Euro Cylinder

    Mole grips worked a treat…. It’s actually frightening how easy it was to snap off with very little force and hardly any noise! glad I’ve swapped them all now
  14. J

    damaged the screw in a Euro Cylinder

    thought it would make more sense to add to this thread rather than posting a new thread that’s pretty much identical and having no way of knowing if the original method worked for the OP. anyhow will give the lock snap method a go in the morning… the current lock is a £5 job, so no doubt it...
Top