Recent content by marky9074

Think I am going to go for a Matki https://www.banyo.co.uk/matki-continental-40-linear-square-rectangular-shower-tray.html Question is, my gap (tile to tile) is 1650mm x 980mm so should I go 1700mm x 900mm and try and chase out and lose 2.5cm at each end or go smaller 1600mm x 900mm and have to...

Any recommendations for a robust shower tray that is going to be straight forward to fit and is not going to crack or break in six months....?

OK, changed over the expansion vessel yesterday. Biggest issue I had was trying to get a 1"BSP to 22mm coupler from Screwfix as tried to click and collect and then payment didn't go through and it then showed as out of stock (as reserved for me presumably) and no amount of persuading to the...

Yup, correct, for cylinder and not boiler (apologies should have mentioned that before). Drip is coming from 15mm outside but assumed from cylinder plumbing as in same location. I'll look for the tun. Noted on servicing, I wasn't aware of that (and it wasn't passed on - ironic given he was a...

Thanks for the confirmation. I've ordered a GWS 18L as a replacement. I'm not sure how that is going to fit as the Imera has a flat part which the installer used to sit flat on the wardrobe shelf. I'll work something out and report back.

I've got what the Potterton (Suprima 60L) manual defines as a fully pumped sealed system. We've seen water coming out of the overflow outside and assume this is because the expansion vessel bladder has zero pressure (well I think that's why water is seen). To pump this up I have turned off the...

Not seen a recent thread on this so hope someone can help. Since being in this house we have always had issues with the mosaic tiles on the floor that needed regrouting once a year. We went away in December and come back to them being 'bouncy' and I said enough was enough and starting ripping...

I just meant that I am on Texecom connect as I did a self install when getting the Smartcom running. It seems I have been a really dumb ass! Both my daughters and my own code were different to what I thought I were... this is why it wasn't working...! I'm still very intrigued to know what those...

I just noticed today that when trying to set the alarm with a user code (as keys and prox ID tag were in the car) nothing happened. This is since setting up the Smartcom and having monitoring set up (albeit the free options). I read somewhere on another thread that if monitoring is on that you...

Thanks for that. Will give it a whirl at the weekend and during the day... I still have to work out how I am going to disconnect the keypad and put cable through plasterboard. I know the tamper will go off as soon as I open the case, but will the alarm sound once its disconnected? Don't fancy...

Smartcom installed (after a bit of hot rewiring/relocating of the Ricochet as the Smartcom cable is so short...) Cloud setup went fine and no issues. Updated Smartcom (prompted me in the app). Initially didn't see the panel update on the cloud, but after a couple of hours they showed up (and...

Hmm, I ordered a flasher interface as well after reading up on updating firmware, but think this was an expensive mistake since it can all be updated through the cloud once the Smartcom is running (and itself updated).

Okay that's ordered, so another journey in the Texecom learning process. I'm usually quite up for a challenge, but with this install I would just settle for something that works for more than a few days at a time!

Thanks for that. My firmware is v5.00.02LS1. Would be great to know what other options are available. I was going to order something like this: Texecom Connect SmartCom Intelligent WIFI Ethernet & App Communicator CEL-0001 | eBay Forgot to say, yeah I did the engineers reset last night and it...

Thanks for your help as always. I must be being a bit thick as I see engineers reset mentioned a few times, but not actually what to do. Is it the same as a normal user reset but with the engineers code? I am wondering whether to just go to a SmartCom setup? I was looking at your web site...