Recent content by Sal99939

  1. S

    Exterior yard wall - knock down and rebuild or strengthen single skin side

    You would re-use the existing bricks? I was thinking to use new bricks as there doesn’t seem to be enough. Also what is the best way to stabilise the party wall its connected to?
  2. S

    Exterior yard wall - knock down and rebuild or strengthen single skin side

    Hi all, Hope you are well. I have a rental property where there was an exterior toilet and storage room. This has been knocked down and the relevant pipe work capped off. What’s left is part a single skin wall and part a double skin wall. I was thinking to have it knocked down and re-built...
  3. S

    Broken stop tap, replacement recommendations

    Hi all, Hope you are well. About 3 years ago we had our combi system converted to un-vented cylinder, I requested a new stop tap along with the renewal of the cold feed to 22mm to assist with flow. They installed the stop tap below, I believe its 25mm to 22mm. The feed in is black plastic...
  4. S

    Fridge that wont level

    Hi, Hope you are well. I am renovating a property, they are keeping their freestanding fridge freezer. It is in good condition apart from the wheels and feet. Floor is level but cant get the fridge to level out, it rocks, have adjusted the feet, there are only two adjustable on the front...
  5. S

    Cleaning up after renovation - removing emulsion and filler from carpet

    Thanks for the responses, I manged to get most of it up using some spot cleaner from world of clean, few faint patches remain but I guess they just need to be worked a little harder. I had multi-solve to hand, tried that on the filler it didn't do much. Did find some silicone and used spot...
  6. S

    Cleaning up after renovation - removing emulsion and filler from carpet

    Hi all, Finishing off renovation and managed to get some matt emulsion, satin wood and wall filler on the carpet. It isn't loads, just spots here and there, whats the best method to get rid of these? Carpet is polypropylene. Any help is greatly appreciated.
  7. S

    Twinplas plastic conversion to square/half round/ogee

    Have been told that Acropol wouldn't form a good bond to the plastic of the twinplas. Have decided to re- do the runs of gutter in new twinplas, I would re-use the exisiting stuff and re-do the joins but we've got additional joins that new runs of 6m lengths would get rid of. Have also been...
  8. S

    Twinplas plastic conversion to square/half round/ogee

    Spoke to local supplier of guttering, fascias etc and they also suggested there are no suitable products to convert from twinplas to any other shape. They re-itterated the faults as they are so common, the joins fail with heat and movement over time and the cavity carries water which leaks out...
  9. S

    Twinplas plastic conversion to square/half round/ogee

    Got the following reply from Osma: Firstly, we do not have any adaptors from our systems to TwinPlas, or any other manufacturers products. In this situation, mid terrace house, there is no easy way to install an alternative system in the middle of a gutter run. Matching up to a standard...
  10. S

    Twinplas plastic conversion to square/half round/ogee

    Hi all, Hope you are well. Currently have the twinplas guttering on my Victorian terraced house. The neighbours have the same twinplas system. As always, its leaking, I believe this is due to the joins (because of expansion) and the centre cavity carrying water. I have had enough, it...
  11. S

    Rak Ceramic thermostatic shower kit

    Hi all, hope everyone is well. Just planning a bathroom renovation and doing some research. Found a thermostatic shower kit from Rak Ceramic, not had any experience with a Rak one myself so just wondering if anyone else has. Only asking as it seems well priced. Link below. I know Rak's...
  12. S

    Re-pointing victorian house

    Responses below, apologies for my lack of knowledge on this, I'm not in the trade and have never had this type of work done before. 1. A previous DPC has been injected - not much use in a cavity wall unless no original DPC exists? Yes no original DPC, the injected DPC was done way before we...
  13. S

    Re-pointing victorian house

    See attached pictures. First 8 pictures are of the rear of the house, south facing. Last 2 pictures are the front. Wouldn't allow me attach more but the front is in better condition than the rear. I have had a quote from a local reputable building company, I've not used them before but they...
  14. S

    Re-pointing victorian house

    I'll get some pictures this weekend. There is some air bricks low down and somebody has used some clear silcone sealant to block it off. Maybe if somebody has had the cavity wall insulation done. The idea with the additional air bricks is to ventialte the cavity and allow it to breathe and...
  15. S

    Re-pointing victorian house

    Hi all, Hope everyone is well. I have a property which needs some re-pointing. The south-side of the property has had its re-pointing done before but it has not been done well. This was before my ownership. It is now in a poor state, so I am organizing to have this done as the weather is...
Back
Top