Search results

I suspect its a faulty device as it doesnt follow the location it follows the device. as to why its faulty I cant see what its doing in terms of resistance etc etc its hard to say.

Its been a while but i can log in on most of them. The issue will be the NVD/DVR/HVR firmware and there plugins, the M series don't need the plugin off top of my head to work under various browsers. Some options appear to be available on some browsers. HIK PRO, appears to resolve mot of these...

whats the resistance showing back at the panel with device not activated? as it follows the device and not the zone when swapping modules, the logic is the device. You can try the slider in a different resistor position and try and select that on the panel. I am going to guess board isn't...

The reality is the device learns on with the correct default settings for that device. other than programming it for behaviour in part set you should really be changing anything else. The sensors sensitivity is set through the device.

Zone setup, zone number, reset starts counting down press reset it deletes off. Press reset again it deletes off the system. Don’t forget to put into commissioning mode after you have learned the device on and to take it off after commissioning has finished

Texecom have several different captures

where you getting this kit from? Your not specific about a few things on your list. 48 Metal takes up a lot of space and had 8 hard wired zones on board. the 64-W only has 4 wired zones on board and 32 wireless., but you can add in terms of expanders another 32 zones either hardwired or...

Why have a wireless keypad if you doing hardwired for some things can you not go hardwired for keypad

Look at the wiring you have to each PIR. iD loops are usually exactly that a loop with each sensor coming off it, however you might be lucky as to what wiring you have available. iD biscuits were fetching good prices secondhand at one time, as they are hard to get hold of so before you throw...

plus postage, need the full picture to best advise. I certainly would replace the whole bellbox. In terms of bell cut off times, its been around a very long time, had to check how long;- 1989 – BSIA installers will fit 20 minute bell cut-outs on all systems from 1990

I am currently not convinced there is a problem. Wrt the panel battery, if that has not been replaced yet it needs testing to see if it has charged back up to an acceptable level. Need to know if alarm works when mains off and just on battery.

I am lost. If the mains is off an panel is working then the back up battery is working. If you have mains on and disconnect the battery is the alarm panel still functioning? Mains power plus battery =alarm works Mains power only = alarm works ? Battery only = alarm works (confirmed)

The alarm panel should not run in battery alone, if it is then you have a mains power issue to the panel and you need to sort that out first. What is the alarm panel?

So it’s not dead, just drained and if charged up should be okay, bell box battery most likely. Normally modern bell boxes ring for 15/20 minutes then stop. If they are activated again the process repeats. On some bell boxes how ring it rings can be determined by the alarm panel and or the...

Take the current battery out and it should have the details printed on it. But looks about right. Not familiar with elmdene units, so don’t know the recommended power or capacity of the top of my head or its dimension for it to fit units holder. Note looks like screw in battery terminals and...

Firstly, are you going to replace the optima where it is now or starting from scratch? On that Panel I can see at least 5 wires connected to the bell terminals. 6 hard wired zones global tamper circuit

original battery June 2006 so 19 years old at least

under the keypad flap

How old is the battery? What is the state of the pcb? (any burn marks around any components) It could in technical terms be .............. some pictures will help speed things up for you

Opening a very old thread isn’t going to help much I fear. might be better to start a thread with some questions on specifics you would like to know more about. No question hardwired is lower maintenance. There are trade offs for both systems.