Search results

hi all, ok I can't work out how to upload a video, anyway that endoscope camera thing turned up, and after pushing through the air brick about 20cm later you see this photo... The sides all stop c33cm so start of inside blocked, but the pipe I was able to go I to c1m before endoscope could go no...

If you meant remove on outside.. 100mm, I did have building control here about a year ago wanting to see how far down the building went for a different face of the building. We went down 9 courses of bricks below ground before guy said stop as we could not get to the foundation start point which...

It's too cold to remove the rad on the inside, to then cut into plasterboard, so that will need to wait until April time. But yes will do. I have the architects set of blue prints and work docs from 1971 as we're given to me by estate owners on moving in, when they converted the stables doesn't...

May help or not, but this was originally a stables many many years ago

Floor is solid floor screed or concrete, tiled on top

No fireplace in that room, the air brick you see is 2metres to the left of the front door

my drain offs for the system are elsewhere... there was in 1970 an oil based boiler c7 metres away from there, maybe legacy noone bothered to remove

ok, any idea why anyone would put those pipes at ground level?

Those two pipes -> scratched and are copper, and calipers measure 14.9mm if helps.

metal, no plastic pipes in this house, pass if lead or copper those pipes are before 2000 easily... i guess could scratch them to see material... no plumbing anywhere at all near this on inside (not drain offs makes no sense either).. as reminder by coincidence one rad other side of the wall...

Hi there, cant surely be suspended floor on the ground, just not possible.... the internal garage we converted was 160mm below this level, and met solid walls internal facing walls. endoscope might be fun actually if has a torch... Only left of field thing i can think of is going back say 200...

Hi all, see photo :) Solid wall, 1780 house, this side of house is c33cm deep, solid of course, then inside battons and plasterboard. After uncovering this air brick which was covered with earth for at least 17 years! (the only one in property as fyi), which goes below DPC, and its two courses...

Ok thanks just ordered some new hinges from Screwfix 2.7mm -> 1.7mm thick, and I'll try 76mm width to 71nm. Friggin cold to change them (have flu right now), but I'll see what I can do this week

Hi, sorry if this is obvious to everyone else :) I took off the three hinges from the front door and replaced them with what appeared same height width, screw hole hinges. The new ones are c102x76 ball bearing hinges. In moment of stupidity I threw away the old hinges and I think they were...

I don't think so, I think best bet is I have some spare plasterboard spray foam, will go round it with that, 20mins later won't ever come out without a utility knife. Ugly yes, but it's hidden under a floor board. (Will do this after the silicon adhesive on the boss fitting.)

Ok thanks. You probably think I am being too nervous, but asked a plumber to come round Friday as directly below that hole is where we keep normally family photo albums (moved now), saved the carpet as the bath of water luckily went down outside of soil pipe and down.

Hello Had a leak in the bathroom, first time in 17 years. Was the waste from bath (40mm pipe with boss type connector thing on it) had popped out. No idea why but I have pushed it back in, however how far should it go into the soil pipe? I had to pull down the ceiling to do this, and now...

Hello A very heavy wooden door, must weight more than me easily, so say 130kg minimum , anyway has three hinges on it. Door I'd guess c50 plus years old. I changed the hinges for ones with same what looked like size, same holes, all fine, but door is now c2mm closer to the lock side, so...

OK tried yes switching all off, trvs to off, hw off, no change. Should of said did that too. Also tried large magnet moving about next to bottom of 3rd and 4th bar thing in case blocked, but really makes no sense, if hot both sides. I'll retry what you said a few more times, over next day...

Hello New radiotor fitted last August, worked fine. Turned on heating today, bled all rads in house and this one, and this one only the front 3 left bars get hot. Hot at trv and lock shield. Removed trv to see if changed anything nope. Noted lock shield settings , opened full, no change, put...