Search results

Manage to blag a £100 discount off my new Miele oven which arrived today. Installed it and all is working perfectly. Poor old replaced Bosch oven looks sorry for itself sitting there upside down where I extracted the bottom element just to have a look at it. The replacement element costs around...

"..They think its all over..." What happens when the new oven arrives tomorrow and the electricity is still being tripped out....:eek: Keep 'em peeled on gumtree.

I am only hearing the haunting phrase of "...throwing good money after bad..." New hideously expensive oven just ordered....well someone has to stimulate the economy...:unsure:o_O

Sunday's roast pork dinner was cooking nicely then suddenly BANG all the lights went out. Soon realised the problem was the oven itself. Switched the oven off and reset the mains RCD and all Ok. Then switched the oven back on and it all lights up ok, reset the clock and then turn the dial and...

Six years on from my last post following the fix above and I can report all trouble free and perfect running on my wonderful Miele W844, now 27 Years Old and looking young and fresh as a daisy (unlike his owner I might add). ...that is up until today and aaarrgghh the dreaded Flashing Red CHECK...

So far so good, the Miele is now 100% dry and I have completed four consecutive washes all of which have been trouble free, no sign of any warning lights. Maybe its my imagination but the clothes seem to be cleaner and smell fresher... I am now going to call this project a success and...

Right, well I decided to remove and clean all the obvious parts including the Pressure Chamber. First was to remove the large black rubber tubing that takes the water from the powder compartments down to a white u-bend chamber that enters the drum. I also removed the white chamber itself by...

Looks like it is the pressure chamber, found these instructions on another site... ...The presssure chamber is connected to a small diameter black rubber tube which either goes to a electronic switch on the front board or to a mechanical pressure switch in the machine. The chamber is...

Oh, right that unit in the picture is at the bottom front of the drum, there is a narrow gauge rubber pipe that leaves that unit and goes right up to the top of the machine and actually passes through the hole on the EL200C board to a connector on the fascia... The Carbon ends of the brushes...

Ok, not sure which item is the Pressure Chamber so can you have a look at the image below to check if this is the unit you mean. Also, if it is, any idea how to remove it ? Also uploaded an image of the brushes for interest...

Ok, you are correct, I have re-tested the Omron about 100 times on all the combinations. Sometimes it appears as though the reaction on the meter is a bit slow, other times it seems to work OK. It is hard to tell if the relay is not working or my connections between the pins was not perfect...

Yes this is the only board except the fascia.. images of board top and bottom attached...let me know if these are good enough to see... thanks

Good points, It was confusing because the problem started with occasionally displaying the "Check Inlet" Red Light and then stopping. If I restarted the program it would most likely be OK. I then checked the inlet water supply which is about 3 Bar and removed, cleaned and replaced the...

I have tried what you suggested. It appears to read around 4 ohms across two of the contacts until I apply the 12V. After this, the reading reverts back to start value of 1. Note, Black Omron G2RL-2 has 6 connections while RT114012 has 3 Black OMRON Relay 4 Ohms between connections 1 and...

No, I didn't, can you give me an idea of how you would make that check ? Thanks SMc

Hi All, I have a Miele W844 with a EL200C board fitted My machine keeps stopping during the cycle with a Red Flashing Light “Check Inlet” OR a Red flashing light “Check Drain”. This does not happen every time, maybe 50%. I have removed the EL200C board and checked the T 6,3A Fuse...

Yep, looks like the CH motorised valve. The heating has been switched off for over 1 hour using the mains isolation switch, however, the underside of the motorised valve is still too hot to touch with my fingers !! Thanks, SMc

Hi, thanks for that tip, would that be the Central Heating Motorised Valve (Only 6 months old!) or could it also be the Water Motorised Valve ? SMc

Hi, The System is standard unvented with a Turkington Engineering Turco 2000 Outdoor System 70/90 Oil fired boiler, a motorised valve and honeywell control units. Regards, SMc

Hi, I have an Oil fired boiler pressurized System. All has been working perfectly OK up until yesterday. Now, The Boiler just keeps working all the time and keeps heating the house 24/7. I have tried the following with no effect. - The digital honeywell wall thermostat has no...