Search results

Thanks for the image, confirms the wiring to the boiler, im using Splan + at the moment so may have to go with the diagram from kim. Any chance you have come across or know of a method to where i can use room stat on x2 terminals (so keep the existing zone valve wiring for CH) and hot water from...

Dan, any chance of your drawings? And any confirmation i can do he priority on my boiler? Don't want to waste installers time trying to get it setup if it won't work...

relay added and extra wire back from hw thermostat off to the ch on. Is there another one knocking around that does it in a different way? Also can i use HW on the x4 board, and CH on the x2 board?

I've got KMB heating and electrical solutions boilermannorthamption.co.uk

Well thanks Dan (the post on the other forum has razor as username) so im guessing he posted it having obtained from you?

Just noticed that my setup may have the HW and CH sides on the X2 board - ie switched live to pin1. Will investigate in the wiring center to see if ch is 0v or 240v.

Hi Razor, Not sure if your getting notifications on this thread, but i think i found a diagram of setting up HW priority on another website on a post (possibly by you!) titled Intergas 's' plan 2 flow settings for SB/OV boilers with WC. So taking that as the basis for my setup, At present i...

I'm in the process of getting a Portman FD30 fire rated pocket door installed - though i've placed it next to an existing brick wall. So far seems to be going well...Using it to seperate out between living/dinning/kitchen and hallway/staircase etc.

In my case, broke in during the day, while alarm was active, at a time when no one was due to be out of the house (but happened to go out on this day for 15 min), and still went through 2 bedrooms, while alarm was ringing, and neighbor was shouting... Some times its just sods law.

For the amount you paid for the power flush the first time, i'd be tempted to buy theMagnaCleanse pro kit and use that yourself a couple of times... Do as many times as you need/want to and know at the end of it what state your left in... plumb Centre have it for £358 at the moment...

Thanks for the replies, it's actually a walk in shower area, and the shower happens to be in the part with the beam... The builders have boxed in pink and then put a second layer for the ceiling itself (there's an air gap) but this was for my own piece of mind...

Would look to see if its possible to push waste out the back wall (over the kitchen) then across to the existing bathroom area for disposal as an option, if that's possible, then the rest would mainly be fresh water plumbing which should be doable?

So i have a steal beam (supporting wall for the first and eventually loft) going through my new ground floor bathroom. BC have specified the beam be boxed in fire rated plasterboard (pink). No problems. Given that its in a bathroom, the walls all have moisture resistant plasterboard(green)...

I got caught out on a similar situation (it wasn't quite 1.8m but about 1m). Inital application was rejected as it was taken from a "built up" patio, even though the neighbors next to me had the same. Had to take from natural ground level next to the house - in my case i ended up having a step...

It's being ripped out as part of a new infastructure build so will end up in bin, I'll be looking to reuse what's there...

It's not being purchased - it's being recycled, the length of the ring is fairly short, max 20 m total - dedicated ring for the room which is across the hall way from the cu. Looking at the numbers I don't till hit anywhere near 13a, so will see if I can rewire the pdu to work on a single...

Fused Spur would work... Though depending on the load, 13A fuse may not be sufficient. Will spend a bit of time and total up requirements. Thanks for the suggestions.

Can i do a straight swap between and existing double socket and a commando socket? The setup i have now is as follows: RCD protected 32A MCB, for a pantry/gadget room (Has sky box, NAS, and a couple of computers, UPS etc). There are TWO double sockets next to each other from which the UPS and...

From an insurance pov, i was once told by a company, if it had a fixed bed in it, it was a bedroom, if it didnt it was some other room...

Could it be the return from this rad is feeding into another rad? And that Rad is off so no flow?